Pivot Bracket Set - Rotary 11265

Automotive Lift Services Verified independent store

→

The Rotary 11265 replacement hardware is the direct replacement for the Rotary lift it came off of. Cross-referenced as ALS-7519-09, it is the genuine Rotary part — same part numbe r, same fit, and same working specification as the one already on your lift. Ordering the Rotary replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same. Specifications Part number: ALS-7519-09 Brand: Rotary Type: Genuine OEM replacement hardware Fits: SPO15, SPO18 Lift type: 2-post lift On lift hardware, fit is the whole job. A pin is not a rod of roughly the right diameter — it is a specific length, a specific fit in its bore, and a specific way of being retained, whether that is an e-clip groove, a cotter key hole, or a shoulder. A bushing is a precise interference in its housing and a precise clearance on its shaft. Manufacturer-spec hardware carries all of those dimensions; the hardware-aisle stand-in carries some of them, and the missing ones become play, wobble, and premature wear. This is a spec-correct replacement for the assembly it belongs to — it goes in the way the original came out, retained the way the original was retained. Related parts for this lift The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit. Lock Spring - Rotary N613-2 1/4" x 1-1/2" Spring Pin Stainless - Rotary - 14427 Spring - Rotary - 14357 Confirm this is the right part before you order Lift manufacturers revise parts mid-production without changing the model name, so the same lift bought two years apart can take two different revisions of the same component. Before you order, find the model plate on the lift — on most 2-post lifts it rides on one of the columns at eye level, on 4-post lifts it is usually on a column or the power-unit side runway — and note the full model number and serial. The serial dates the lift to a production run, and that is what decides which revision fits. If the plate is painted over or missing, take a photo of the part you are replacing next to a tape measure and send it to us. Between the dimensions, the mounting pattern, and what lift it came off of, we can almost always identify the exact part before you spend money on the wrong one. Lay the new piece against the old before installing: length, diameter, groove and hole positions, thread pitch. If the old part is too worn to compare against, check the new part in its bore or against its mate by hand — it should fit the way a machined part fits, snug and smooth, not loose and not forced. Replace the retaining clips and keys while you are there; they are one-use money. Retention is not optional. A pin without its e-clip, cotter key, or bolt is a pin working its way out under vibration, and what it drops depends on where it lives. If the retainer came off damaged, replace it — never spring a used clip back on and call it held. Why buy your Rotary replacement hardware from Auto Lift Services We install, inspect, and repair Rotary lifts every week — the ALS-7519-09 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302. We confirm the right part for your lift's serial and production year before you order. Every part ships as genuine Rotary — no aftermarket substitution unless you specifically ask for an aftermarket equivalent. If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job. About this 11265 pivot bracket Sourcing the correct 11265 pivot bracket is not the spot a shop wants to gamble. This piece sits inside a load path the lift manufacturer engineered to specific tolerances, and a substitute that looks close but is off by even a small margin can transfer load onto a neighboring component that was not designed for it. We stock this exact part to the OEM specification the original manufacturer publishes, which is why techs who have been through a bad aftermarket cycle keep coming back to us for the same replacement whenever their next need comes up. Technical specification & installation notes Cycle life on this piece depends heavily on operating conditions. In a typical commercial repair shop running 6-10 lifts per day, the 11265 pivot bracket should deliver five to eight years of service before showing measurable wear against the OEM inspection specification. In a high-volume tire or alignment shop running 20+ lifts per day per bay, expect service every three to five years. It is designed to be a serviceable component; when it does wear it wears within safe operating margins that trigger visible symptoms — drift, uneven wear, minor leakage — well before failure becomes a safety issue. Shipping & ordering Shipping runs 3-5 business days on standard ground to the lower 48 states. Expedited overnight and two-day options are available; call 800-674-9302 before ordering to quote expedited freight. We stock the 11265 pivot bracket in Iowa and ship same-day for orders confirmed before 2 PM Central. Orders that come in later than that or on a Friday afternoon pick up on the next business day. A tracking number gets emailed to the address on the order the moment the package leaves our dock. Warranty coverage Consumables and wear parts like this are covered under the manufacturer defect warranty for twelve months. Because the 11265 pivot bracket is a component that eventually needs replacement in normal operation, warranty coverage specifically addresses failure due to manufacturing defect, not failure due to normal end-of-life wear. Our team can help distinguish between the two on a phone call if there is any question after installation — call 800-674-9302 and describe the failure pattern; we will tell you honestly whether it looks like a warranty case. Cross-reference & fitment Cross-reference on the 11265 pivot bracket is straightforward: match the OEM part number from the lift's parts breakdown against the number on your original invoice. If the numbers match, the component fits. If your lift's parts breakdown lists a superseded or alternate number, we accept the superseded value on the phone as confirmation of fit. When a manufacturer has issued a running change during production, we track the change in our catalog so ordering by the older number automatically pulls the current-spec replacement. Questions about the 11265 pivot bracket? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day. Show more