All vehicles that use this remote are onboard programmable, meaning you can program the vehicle to accept new remotes yourself without any special tools or knowledge. Free phone tech support is available if needed. Remote For Chrysler Dodge Eagle Mitsubishi: This remote's FCC ID is GQ43VT6T. The OEM part numbers are: MR123944 and MR122506. It sends it's signals on a frequency of 315 Mhz. Free programming instructions. Remote is tested on keyless entry signal testers to ensure proper functioning. Programming Procedure: For 1995-2000 Sebring: 1. Locate the Data Line Connector (DLC) underneath the driver's side dashboard, either to the left or the right of the steering column base. The two views in figure b are looking straight into the cavities of the DLC. We will be working with the row (terminals 1 through 8) on the wider side of the DLC. Use the view that matches the orientation of the DLC in your vehicle to identify terminals 1 and 4.2. Insert keys in ifnition and leave it in the OFF position.3. Make sure there are metal contact pins in the terminals 1 and 4 and connect the Data Line Connector (DLC) terminal 1 to terminal 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure). Make sure you know which terminals are 1 and 4.4. Within 10 seconds after connecting the jumper wire, press the Hazard Switch (Emergency flashers) 6 times. The doors will automatically lock and unlock once to indicate that the system is in programming mode.5. Press either the Lock or Unlock button on the transmitter to be programmed three times within 10 seconds. Upon successful programming, the doors will locksm and unlock once.6. Within one minute repeat the previous step with each additional transmitter you wish to program including any existing transmitters (up to a total of 4). After completing each remote programming the doors will lock and unlock once.7. Disconnect the jumper wire and remove the keys from the ignition/8. Test the remote. For 1995-2000 Avenger, 1993 Stealth, 1996-1998 Talon: 1. Locate the Data Line Connector (DLC) underneath the driver?? side dashboard. The DLC is typically located either to the left or the right of the steering column base. Use the figure to the side as a map for your DLC (they usually aren?? numbered). The view in figure b, is looking straight into the cavities of the DLC. Notice how the DLC is tapered on both ends: we will be working on the wider row of cavities (1 through 8 in figure b.).2. Insert keys in ignition and leave in the OFF position.3. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Line Connector (DLC) terminal 1 to terminal 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure). Make sure you know which terminals are 1 and 4.4. Within 10 seconds after connecting the jumper wire, turn the ignition switch to the ACC position and then back to OFF NOTE: The doors will automatically lock and unlock once indicating that the system is in the programming mode.5. Press either the LOCK or UNLOCK button on the transmitter to be registered three times within 10 seconds. Upon successful programming, the door will lock and unlock once.6. If there is a second transmitter, press the LOCK or UNLOCK button three times within one minute and the doors will lock and unlock once to confirm successful programming.7. Disconnect the programming wire and remove the keys from the ignition. For 1994-1995 Stealth: 1. Ensure that central locking system is functioning properly.2. Access central locking system control module behind the left side trim panel.3. Set code registration switch on module to SET I position.4. Press any button on first remote to be programmed. If only 1 remote is to be programmed then position the switch to FIX and check remote operation.5. Position code switch to SET II.6. Press any button of a second remote.7. Position code switch to FIX.8. Ensure central locking system is operating correctly using both remotes. For 1995-1999 Eclipse: 1. Locate the Data Line Connector (DLC) underneath the driver?? side dashboard. The DLC is typically located either to the left or the right of the steering column base. Use the figure to the side as a map for your DLC (they usually aren?? numbered). The view in figure b, is looking straight into the cavities of the DLC. Notice how the DLC is tapered on both ends: we will be working on the wider row of cavities (1 through 8 in figure b.).2. Insert keys in ignition and leave in the OFF position.3. Make sure there are metal contact pins in terminals 1 and 4 and connect the Data Line Connector (DLC) terminal 1 to terminal 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure). Make sure you know which terminals are 1 and 4.4. Within 10 seconds after connecting the jumper wire, press the Hazard Switch 6 times. The doors will automatically lock and unlock once indicating that the system is in the programming mode.5. Press either the LOCK or UNLOCK button on the transmitter to be registered three times within 10 seconds. Upon successful programming, the door will lock and unlock once.6. If there is a second transmitter, press the LOCK or UNLOCK button three times within one minute and the doors will lock and unlock once to confirm successful programming.7. Disconnect the programming wire and remove the keys from the ignition. The following vehicles can use this remote when equipped with the factory keyless entry system: Chrysler Sebring (1995), Chrysler Sebring (1996-2000), Chrysler Sebring (1996-2000), Dodge Avenger (1995-2000), Dodge Stealth (1994-1995), Eagle Talon (1996-1998), Mitsubishi Eclipse (1995-1999).
