Product Description Features: Data backup.you can backup all the enrollments data into a memory IC and then restore to other same devices. Delete/Add cards by master card, Anti-probe the password Add ID cards by the room number,such as can name cards to the controller as "201"(201 is a room number),emember the cards but not its real number so that you don't have to remember all the cards' number especially when a card lost. 5.Capacity can be extended up to 16K if you need. 6. It has 3 models those are compatible with Mifare1/Hid/EM , please look the tablet below. Parallel all the models: model FC-198E FC-198E16 Card EM EM User capacity 1000 16,000 All models support: open the door by password, by card + password , manage the device by master card, data backup and restore by memory IC. Extendable Optional:Remote control,RFID reader Card Type: Card type function 1 Common use card 2 Daytime using card,invalid during evening 3 Password attached card,must typing in PW after card reading whenever 4 Password attached during evening.Only card reading is valid during daytime Pin Description and wiring diagram: PIN Symbol Description 1 +12 V DC9-13.8V 2 GND Ground 3 NO normally open of relays, capacity DC10A/30V 4 COM common point of relays, capacity DC10A/30V 5 NC normally close of relays, capacity DC10A/30V 6 OPEN Connect to open switch 7 DOOR Connect to door magnetic sensor 8 ALM Alarm bell output port, current load 100mA 9 WG0 Wiegand 26 reader data lines (data 0),when a reader extended 10 WG1 Wiegand 26 reader data lines (data 1) ,when a reader extended 11 BELL doorbell switch, Operation manual: Function Key Log In 0*password# .Default administrative password:1234 Log off 0*# The functions below should be operated in a Log in status Change password 1*newpassword# (password should be 4~6 bits) Dispatch user PW 2*userpassword#(user password should be 4~6 bits) Delete user PW 3*user password# Delete all user PWs 3*9*9# Dispatch type 1card 4*1# card reading(if more cards,can read card continuously) Dispatch type 2 card 4*2# card reading(if more cards,can read card continuously) Dispatch type 3 card 4*3# card reading(if more cards,can read card continuously) Dispatch type 4 card 4*4# card reading(if more cards,can read card continuously) Dispatch a remote 4*5# pressing any key of the remote,the device beep once means OK. Delete cards 5*card number# (card number is a 10 bits printed on card) Delete all cards 5*9*9# (the device beep once means finished) Delete a card type 6*card type# Delete all cards&PW 6*9*9# Setup to night mode 7*password# Setup to Normal Open 8*password#(conveniently for going to work every morning) Setup open delay 9*seconds# (seconds is a 0~99 digit means the duration of delay) Setup fault PW times 10*fault times#(a 2~9 digit,means fault PW entering times,default is 5) Setup device suspend time 11*suspend time#(1~99 ,means 1~99 seconds,default is 10) Restore the Manufacture setup 12*# Setup stress PW 13*stress PW#(4~6 bit) The functions below should be operated in a normal status PW open PW # Card open Card reading,(if a PW needed,press the PW) On/Off the night mode 7*PW # On/Off NO status 8*PW # Modify the user PW after card reading,press *1* new password# during green light flashing Turn on the Stressing Alarm Stress PW# Turn off the Alarming Read any authorized user card Others press ** anywhen will exit if the operation is right,the buzzer will sounda long beep,if wrong operation,3 short beep. Press and hold the reset button for 1 second,one beep,all the setup will be restore to manufacture default. Press and hold the reset button for 3 seconds,not only restore the manufacture default,but also delete all the data including dispatched cards and PW
Related
Related
Related
Related