USA Made - ADA Compliant Truncated Domes Our ADA compliant, USA made 24" x 48" truncated domes are designed to ensure safety and accessibility for all pedestrians. These ADA pads, measuring 24" x 48" and weighing 17 lbs each, provide essential tactile ground surface indicators that comply with ADA regulations. Ideal for installation on dry concrete, these ADA mats are used to create a detectable boundary between pedestrian walkways and vehicular traffic areas. Sandbaggy ADA warning pads have a max UV protection for an extended life under the sun. (More sizes and styles available) ⚠️ Please Note 5 Year Warranty Includes: Adhesive and fasteners ADA / DOT compliant Installation Instructions Below Specs Country of Origin: USA Material: Glass Reinforced Thermoset Composite Width: 24" (2 ft) Length: 48" (4 ft) UV Protected: Yes Color: Yellow Weight: 17.3 lbs Technical Specifications Property ASTM Standard Result Slip Resistance ASTM C1028 Dry .93 / Wet .76 Impact Resistance ASTM D256 8.0 Izod ft-ibs / in (notch) Adhesion Bond Strength ASTM C482 152 psi UV Resistance – Fade Cap Y (LVR) Brick Red 5-15 Safety Yellow 25-50 Water Absorption ASTM C373 0.3 – 0.6% Compression Strength ASTM D695 30,000 psi Flexural Strength ASTM D790 18,000 psi Tensile Strength 1/8″ ASTM D638 9,000 psi Color Integral Throughout Product Yes Dome Height — 0.2″ Dome Base Width — 0.9″ Dome Top Diameter — 0.45″ Dome Spacing — 2.4″ center-to-center UL Flammability UL 94 V-0 94V-0@3/32″ Flame Resistance SecondsIgnition TimeGurning Time ASTM D-229 12065 Flame Spread Index, 1/4″ ASTM E84 ‹25 Freeze-Thaw Durability ASTM C1262-08 Pass Features 5-Year Ironclad Warranty - Built for punishment. Fully Backed. Most competitors offer no warranty. ADA Compliant Warning Pads: Designed to meet ADA standards, these truncated domes ensure compliance with federal and state regulations. They feature 2.4" center-to-center spacing, with a 0.9" base and 0.45" top diameter. Easy Surface Mount Installation: Includes adhesives and fasteners for secure attachment. Pre-formed fastener locations ensure error-free installation, creating a durable and reliable solution. Slip, Impact, & Wear Resistant: Made from a tough glass reinforced thermoset composite, this ADA pad is built to handle heavy foot traffic, mobility device impact, and harsh weather. Strong Yet Flexible: The semi-rigid composition with 30,000 psi strength provides durability while allowing the pad to conform to ramp irregularities for a secure fit. Safe & Smooth Transitions: Perimeter beveled edges ensure a trip-free transition, enhancing safety for pedestrians and mobility device users. MAX UV Protection for extended life under the sun. Compliance and Application These ADA warning pads fully comply with ADA requirements for surface height transitions, eliminating trip hazards and ensuring a smooth rolling transition for all users. These ADA mats are suitable for use in various locations, including ramps, stairs, curb cutouts, and along paths of travel. They provide essential tactile feedback for visually impaired pedestrians and alert all users to changes in surface levels or potential hazards. Please consult local and state regulations, as specific requirements, such as those outlined in California Title 24, may apply. California, for example, requires a minimum 3-foot dimension and safety yellow color for truncated domes. Always check with local access compliance agencies before purchasing ADA signs or products to ensure full compliance with regulations. Installation Instructions Confirm that the concrete substrate is in full compliance with Federal, State, local standards, building codes, project plans and specifications, prior to installation of Sandbaggy panel. Installation surface area must be cleaned of debris, dust, oil and grease, making sure the area is completely free of surface moisture. It’s recommended to use a diamond cup grinder, pressure shot-blaster or (at a minimum) use a wire brush to remove any dirt or foreign material. Lay out the panel on the concrete substrate and mark around the panel corners with a pencil to identify the designated installation location. (Not recommended or warranted for asphalt installations) Remove the panel from the marked installation area, flip over and apply a continuous bead of NP-1 adhesive to the back of the panel approximately ¾” from the edge following the scored perimeter and center cross pattern. Place panel in marked installation area. Make necessary adjustments prior to fastening. Standing on the panel using a hammer drill with a 5/16” carbide tipped bit, drill a hole a minimum of 2” deep. Clean drilling debris from holes. Begin in the middle, then work your way towards the edges, inserting anchors and #14 stainless screws into the pre-formed countersunk fastener locations. Using a #3 square head bit, apply downward pressure with a screw gun, press until the anchor goes through the panel and is flush with the surface of the concrete substrate. Tighten the screw until the screw is in full contact with the countersunk fastener surface of the panel. Following panel installation, caulk around the perimeter of the panel with NP1 or equivalent. Blend and taper the caulking smooth around the perimeter in a cove profile between tile and adjacent concrete substrate. Sandbaggy Public Safety Equipment Protect your community with reliable public safety products from Sandbaggy. Our lineup includes ADA tiles, chain link fences, sign posts, safety railings, delineator posts, and more — all designed to enhance safety, organization, and accessibility. We offer a wide variety of products for municipalities, contractors, and public works projects, providing practical, long-lasting solutions for traffic control, pedestrian safety, and site management. Many of our products meet local and federal standards, ensuring compliance, durability, and easy installation — keeping your projects running safely and efficiently. FAQ What are ADA warning pads and why are they important? ADA warning pads, also known as detectable warning surfaces, are textured ground surfaces designed to alert visually impaired pedestrians of potential hazards. These pads ensure safety, signaling environmental changes such as street crossings, transit platform edges, and hazardous vehicular ways. Where are ADA tiles typically installed? ADA warning pads are typically installed in locations where there is a transition between pedestrian and vehicular areas or where there are potential safety risks. Common installation sites include curb ramps, sidewalks, the edges of transit platforms, pedestrian crossings, etc. Are ADA warning pads required by law? Yes, ADA warning pads are required by law under the Americans with Disabilities Act (ADA). The ADA mandates that public and private facilities ensure accessibility for individuals with disabilities, including installing detectable warning surfaces in specific locations. What materials are ADA warning pads made from? ADA warning pads are made from various durable materials designed to withstand heavy foot traffic and environmental conditions. Common materials include cast iron, stainless steel, composites, polymer concrete, and high-density polyethylene (HDPE). How do ADA warning pads help individuals with visual impairments? ADA warning pads assist individuals with visual impairments by providing a tactile surface that can be detected using a cane or underfoot. The raised, truncated domes on the pads create a recognizable texture, alerting users to changes, such as approaching street crossings, platform edges, etc. How does this product compare to Detectable Warning's Alert tile? Our product has the exact same specs as Detectable Warning's Alert tile. What other names do these ada truncated domes go by? This product may also be known as detectable warning panels truncated dome pavers detectable warning plates surface applied truncated domes alert tile alerttile
Related
Related
Related
Related