{ "@context": "https://schema.org", "@type": "FAQPage", "mainEntity": [ { "@type": "Question", "name": "How do I choose the right quantity pack for my project?", "acceptedAnswer": { "@type": "Answer", "text": "For one-off prototypes or repairs, a 10-pack is typically sufficient. Hobbyists building multiple circuits generally find a 30–50 pack more economical. For production runs or classroom kits, the 100-pack offers the best per-unit value." } }, { "@type": "Question", "name": "What does DPDT mean and why does it matter?", "acceptedAnswer": { "@type": "Answer", "text": "DPDT stands for Double Pole Double Throw. It means the switch controls two separate circuits simultaneously and can route each to one of two outputs. This is commonly used for motor direction reversal, signal routing, and circuit isolation in DIY electronics projects." } }, { "@type": "Question", "name": "What are the typical electrical ratings for this type of slide switch?", "acceptedAnswer": { "@type": "Answer", "text": "Miniature PCB slide switches of this type are generally rated for low-voltage DC applications — typically 0.5A at 50V DC or similar. They are not designed for mains AC voltage. Always verify the datasheet for your specific application before use." } }, { "@type": "Question", "name": "Can this switch be used outdoors or in humid environments?", "acceptedAnswer": { "@type": "Answer", "text": "These switches are designed for indoor PCB and breadboard use. They are generally not sealed or rated for outdoor or high-humidity environments. For outdoor applications, a conformal-coated or IP-rated switch is recommended." } }, { "@type": "Question", "name": "Is this switch compatible with standard breadboards and PCBs?", "acceptedAnswer": { "@type": "Answer", "text": "Yes. The 6-pin through-hole layout is designed to fit standard 2.54mm (0.1\u2033) pitch PCBs. Breadboard compatibility depends on pin spacing — confirm the pin pitch matches your breadboard's hole spacing before inserting." } }, { "@type": "Question", "name": "How do I wire a DPDT slide switch for motor direction control?", "acceptedAnswer": { "@type": "Answer", "text": "In a typical H-bridge-style wiring, the two center pins connect to your power supply, and the four outer pins connect to the motor terminals in a cross pattern. Sliding the switch reverses the polarity across the motor, changing its direction. Refer to a DPDT motor reversal wiring diagram for your specific circuit." } }, { "@type": "Question", "name": "What is the pin pitch and physical footprint of these switches?", "acceptedAnswer": { "@type": "Answer", "text": "Most miniature 6-pin DPDT slide switches of this style use a 2.54mm (0.1\u2033) pin pitch in a 2\u00d73 grid layout. The overall body dimensions are typically around 8\u201312mm in length. See variant options or contact us to confirm exact dimensions for your design." } } ] } 6-Pin DPDT Slide Switch — Reliable 2-Position Toggle for PCB & Breadboard Projects When your circuit needs a clean, mechanical way to switch between two states — reversing a motor, toggling a signal path, or isolating a sub-circuit — a loose wire or jumper just doesn't cut it. Makers, electronics students, and hardware prototypers need a dependable 6-pin DPDT slide switch that drops straight into a PCB or breadboard without fuss. Each pack contains miniature through-hole DPDT slide switches with a 6-pin (2×3) layout, designed for standard 2.54mm (0.1") pitch PCBs. The compact body — typically 8–12mm in length — fits neatly on breadboards and perfboards. Available in pack sizes from 10 to 100 pieces to match your project scale. These switches are well-suited for Arduino and Raspberry Pi accessory boards, DIY audio signal routing, small DC motor direction control circuits, and educational electronics kits where a tactile 2-position toggle switch is needed on a breadboard or soldered PCB. 🔌 Compatibility: Designed for standard 2.54mm (0.1") pitch PCBs and through-hole soldering. Breadboard fit depends on pin spacing — verify before inserting. Not rated for mains AC voltage. ⚠️ Spec Note: Exact body dimensions and electrical ratings vary by production batch. If your design has tight clearance or specific current requirements, contact us to confirm before ordering. ✅ Key Features of These 6-Pin DPDT Slide Switches 🔀Double Pole Double Throw (DPDT) — Controls two independent circuits simultaneously, making it ideal for DC motor direction reversal and dual-channel signal switching on a single PCB. 📐Standard 2.54mm Pin Pitch — The 6-pin through-hole footprint aligns with the most common PCB grid spacing, so it drops into your existing board layout without custom routing. 🧲Positive 2-Position Detent — The slide actuator locks into each position with a tactile click, preventing accidental mid-position states that can cause circuit faults in breadboard toggle switch applications. ⚡Low-Voltage DC Rated — Suited for 3.3V and 5V logic-level circuits as well as small DC motor loads — the typical use case for Arduino slide switch and microcontroller projects. 📦Multi-Pack Value Options — Choose from 10 to 100 pieces per order, so whether you're prototyping a single board or stocking a maker lab, you only buy what you need. 🔧Solder-In Installation — Through-hole pins allow hand-soldering with a standard iron, no SMD reflow required — accessible for hobbyists and students building their first electronics DIY project. 📐 Technical Specifications — 6-Pin DPDT Slide Switch Switch Type DPDT (Double Pole Double Throw) Number of Positions 2 Pin Count 6 pins (2×3 through-hole layout) Pin Pitch Typically 2.54mm (0.1") — See variant options Body Length Typically 8–12mm — Contact us to confirm Mounting Type Through-hole (PCB solder-in) Actuator Type Slide / Toggle Voltage Rating Typically up to 50V DC — Contact us to confirm Current Rating Typically 0.3A–0.5A DC — Contact us to confirm Operating Temperature See variant options Material Plastic housing, copper alloy contacts Finish See variant options Pack Sizes Available 10, 20, 30, 40, 50, 100 pieces Compatible Standards Standard 2.54mm PCB grid; breadboard compatibility — verify pin spacing ❓ Frequently Asked Questions How do I choose the right quantity pack for my project? For one-off prototypes or repairs, a 10-pack is typically sufficient. Hobbyists building multiple circuits generally find a 30–50 pack more economical. For production runs or classroom kits, the 100-pack offers the best per-unit value. What does DPDT mean and why does it matter? DPDT stands for Double Pole Double Throw. It means the switch controls two separate circuits simultaneously and can route each to one of two outputs. This is commonly used for motor direction reversal, signal routing, and circuit isolation in DIY electronics projects. What are the typical electrical ratings for this slide switch? Miniature PCB slide switches of this type are generally rated for low-voltage DC applications — typically 0.3A–0.5A at up to 50V DC. They are not designed for mains AC voltage. Always verify the datasheet for your specific application before use, or contact us to confirm the exact rating for your batch. Can this switch be used outdoors or in humid environments? These switches are designed for indoor PCB and breadboard use. They are generally not sealed or rated for outdoor or high-humidity environments. For outdoor applications, a conformal-coated or IP-rated enclosure switch is recommended. Is this switch compatible with standard breadboards and PCBs? Yes. The 6-pin through-hole layout is designed to fit standard 2.54mm (0.1") pitch PCBs. Breadboard compatibility depends on pin spacing — confirm the pin pitch matches your breadboard's hole spacing before inserting. Most standard full-size and half-size breadboards use 2.54mm spacing. How do I wire a DPDT slide switch for DC motor direction control? In a typical wiring setup, the two center pins connect to your power supply (V+ and GND), and the four outer pins connect to the motor terminals in a cross pattern. Sliding the switch reverses the polarity across the motor, changing its rotation direction. Refer to a standard DPDT motor reversal wiring diagram for your specific circuit layout. What is the pin pitch and physical footprint of these switches? Most miniature 6-pin DPDT slide switches of this style use a 2.54mm (0.1") pin pitch in a 2×3 grid layout. The overall body length is typically 8–12mm. Contact us to confirm exact dimensions if your PCB layout has tight clearance requirements. 🛒 Select your quantity above, then add to cart — ships from our US warehouse.
