AES E-Loop EL00C Commercial Wireless Detection System

Elite Gates Verified independent store

→

Surface-Mounted Wireless Vehicle Detection for Automatic Gates The AES E-Loop EL00C-RAD Commercial is a surface-mounted wireless vehicle detection system for automatic gates, comme rcial entrances, warehouses, factories, and other controlled vehicle access points. It eliminates the need to cut pavement and install a traditional wired inductive loop, allowing the sensor to be secured directly to the driving surface and communicate wirelessly with the included eTrans receiver. The EL00C-RAD offers Exit, Presence, and Parking modes, automatic calibration, 128-bit AES encrypted communication, IP68 environmental protection, and configuration through the AES e-CONNECT mobile app. Depending on the selected kit, the eTrans receiver supports up to 50, 100, or 200 e-TX remotes, with all three versions supporting up to 4 e-Loops. Key Features Surface-mounted wireless vehicle detection without cutting pavement for a conventional loop Designed for commercial and industrial automatic gate applications Exit, Presence, and Parking operating modes Up to 10 years battery life in Exit Mode Up to 4 years battery life in Presence Mode 128-bit AES encrypted wireless communication Automatic calibration for simplified setup IP68 ingress protection Adjustable radar and magnetometer detection settings AES e-CONNECT app support for configuration and diagnostics Each receiver supports up to 4 e-Loops Receiver options support up to 50, 100, or 200 e-TX remotes Designed for above-ground installation Technical Specifications Manufacturer: AES Product Family: e-Loop Commercial Model: EL00C-RAD Product Type: Surface-mounted wireless vehicle detection system Operating Modes: Exit, Presence, Parking Radio Frequency: 433.39 MHz Modulation: FSK Bit Rate: 100 kbps Bandwidth: 50 kHz Antenna Type: PCB Nominal Output Power: 14 dBm Receive Sensitivity: -126.2 dBm Wireless Security: 128-bit AES encryption Power: 4 x 3.6V 2700 mAh batteries Standby Power: 14 µA Activation Power: 40 µA Battery Life: Up to 10 years in Exit Mode; up to 4 years in Presence Mode Dimensions: 224 x 224 x 36 mm Weight: 1000 g Ingress Protection: IP68 Operating Temperature: -40°C to 80°C Mounting: Above-ground surface mounting Radar Detection Range: 0.2 m minimum; 1.8 m default; up to 2.0 m maximum Magnetometer Range: Approximately 0.5 m high, 1.0 m medium, and 1.5 m low detection range Mobile Configuration: AES e-CONNECT app Safety Compliance: Tested to CE Variants EL00C-RAD: Puck only EL00C-RAD-K: Includes eTrans50; supports up to 50 e-TX remotes and 4 e-Loops EL00C-RAD-KT: Includes eTrans100; supports up to 100 e-TX remotes and 4 e-Loops EL00C-RAD-KLT: Includes eTrans200; supports up to 200 e-TX remotes and 4 e-Loops Installation and Operating Notes Install the e-Loop centrally in the normal vehicle path on a clean, level, secure surface with the directional arrow facing the gate. Avoid mounting near high-voltage cables or other sources of electrical interference. Exit Mode sends a single activation pulse when a vehicle is detected. Presence Mode holds the relay while the vehicle remains detected, while Parking Mode provides similar operation with a slower latch and reduced power consumption. Presence Mode is intended for vehicle detection only and must not be used as a pedestrian or personal safety device. Conclusion The AES EL00C-RAD Commercial e-Loop provides wireless vehicle detection without the pavement cutting and buried wiring required by a traditional inductive loop. Choose the EL00C-RAD-K, EL00C-RAD-KT, or EL00C-RAD-KLT based on the required e-TX remote capacity; each version supports up to four e-Loops. Installation / User Manual Show more