Atomium MGSB | Manual transmission
EFFECTS OF APPLICATION Atomium MGSB creates conditions for gradual restoration of worn friction surfaces of gear teeth and synchronizer couplings. As result a new protective metall ic layer appears on the friction surfaces which may retain dense oil film due to its microporous structure. Optimized friction clearances and improved lubrication allows you to solve the following tasks: TO REDUCE OR COMPLETELY ELIMINATE THE HUM, NOISE AND VIBRATION WHEN THE TRANSMISSION IS RUNNING Restored shape of the gear teeth ensures their correct and smooth engagement. In addition, their contacts are softened by a denser oil film on the surface of the teeth. It eliminates micro-impacts of teeth and thus reduces the hum and noise during operation. Noise and vibrations may be also caused by worn bearings. It gives higher tone of hum. Atomium MGSB is able to restore them along with gears as they are lubricated by the same oil. Atomium oil additive is effective regardless of what specific gear pair is noisy. All of them are lubricated with the same oil and are being treated equally. Restoration process goes on until the worn details are restored to the optimal shape. Atomium MGSB may be useful also to facilitate running-in of new gearboxes. The running-in process goes faster and quitter. TO FACILITATE GEAR SHIFTING, GET RID OF THE "CRUNCH" WHEN SWITCHING In manual transmission there may appear troubles in gear shifting. Gears are not shifted from the first stick movement, the switching is hard, some crunching noises may appear. Very probably it shows that teeth of the synchronizer clutch are worn and are not engaged smoothly. Tribotechnical gearbox additive Atomium MGSB restores the surfaces of the teeth on the synchro couplings. In addition, the restored surfaces retain a denser film of oil. This makes it easier for the coupling to engage with the locking ring and then with the transmission gear. Gear shifting becomes smooth, quiet and fast. TO REDUCE FUEL CONSUMPTION BY INCREASING THE VEHICLE'S FREE RUN A dense oil film on the surfaces of the teeth ensures their smooth entry into and exit from the engagement, which reduces energy losses during transmission operation. This increases the run-out-free running of the car in neutral gear, and leads to a reduction in fuel consumption. TO EXTEND THE LIFESPAN OF THE GEARBOX A denser oil film on the surfaces of parts treated with Atomium gearbox additive significantly slows down their further wear and protects them when working with high loads. This extends the service life of the entire unit, allows you to postpone the repair or replacement of the manual transmission even if the first signs of wear appear. HOW IT WORKS Tribotechnical compound contains particles of the active mineral. Being in transmission oil they time to time get into the local zones around a point of surfaces’ contact. There are a high local pressure and the temperature which exceeds 1000 °C. In those conditions mineral get able to activate metallic bonds, which let the surface to capture and attach metal microparticles from the oil. Gradually, a solid metal protective layer is formed on the entire worn surface. The mineral itself remain in the oil and initiates restoration process in other points. Protective layer is hard and smooth, which reduces friction. It also has a porous structure with a large number of micro-hollows. They are filled with oil, which forms a continuous film due to surface tension forces. This oil film is never completely separated from the surface of the part, does not flow down even during a long idle time. The protective layer itself can withstand heavy loads due to microhardness and microelasticity compared to the factory surface. Restored shape and effective lubrication allow the parts to perform their functions as it was laid down in the design of the unit, which improves performance parameters of the whole mechanism. HOW TO USE Gearbox additive Atomium MGSB must be added once to the transmission oil through the standard oil filling hole. To continuously maintain the recovery effects it is recommended to add the compound with each regular oil change in the transmission. The compound (gearbox oil additive) is designed to protect against wear, extend the service life and restore the characteristics of mechanical gearboxes of passenger cars, including robotic transmissions of any design. Atomium MGSB should be added to the manual or semi-automatic gearbox just once. In case if a transmission fluid replacement is planned - change it first and then add compound to the new oil. Mechanical and robotic gearboxes are treated as follows: Warm up the transmission to operating temperature (normal operation). Turn off the engine. Carefully mix the bottle with the composition, so that the sediment at the bottom is distributed throughout the entire volume of the liquid. Pour 1 bottle of the compound into the gearbox through the oil filling hole of the unit. Right after adding the compound, make a trip by car for 20-30 minutes in normal operation. 1 bottle of Atomium MGSB is enough to handle any transmission with a volume of transmission fluid up to 3.5 litres. After that the car can be used as usually. For long-term trouble-free operation of the transmission, it is recommended to use compound Atomium MGSB after each scheduled replacement of transmission oil. Precautionary measures: Does not pose a health hazard under normal conditions of use. In case of skin contact, wash the exposed area with warm water and then with soap and water. In case of contact with eyes, rinse them with plenty of water. In case of contact with the digestive system, consult a doctor. Notes: Shelf life is 5 years. The date of manufacture is indicated on the bottle. It is not recommended for use in mechanical failures of parts and assemblies. Additive Atomium MGSB is compatible with all types of transmission oils, including ATF-based oils. 1 bottle of Atomium MGSB is enough to handle any transmission with a volume of transmission fluid up to 3.5 litres. The sediment at the bottom of the bottle is the main working element of the compound of Atomium MGSB - microparticles of minerals. It is extremely important to thoroughly mix the contents of the bottle before pouring it into the gearbox. (The colour of the sediment may vary from light green to dark grey and black depending on the production batch). The composition of the "manual transmission" does not interact with clutch clutches, does not affect the wear and performance of the clutch discs, does not prevent clutch failures. An overdose of 1.5-2 times is not dangerous for the transmission and does not disrupt its operation. Tribotechnical Compound Atomium MGSB does not affect the characteristics and condition of parts made of composite materials, ceramics and rubber products.
