Bambu Lab Engineering Bed Plate One Build Plate for All Filaments With a simple layer of glue, the Engineering Plate is compatible with our entire filament lineup, it's the perfect go-to solution when you're not sure which plate to use. Durable Smooth Surface Coating The refreshed coating significantly improves the plate's temperature, scratch, and corrosion resistance. Built to withstand prolonged high-temperature printing and hundreds of washes and peels, its smooth, dependable surface guarantees stable adhesion every single time. Smooth & Natural Surface Finish The smooth base coating can impart a smooth & flat texture to the bottom surface of the printed object, better blend-in with other surfaces. Considerations Before printing with any filament, it is recommended to apply glue on the Engineering Plate. Applying solid glue can make part removal easier, but since solid glue has a certain thickness and is difficult to apply evenly, the printing stability and first-layer quality are usually not as good as when using liquid glue. On the other hand, liquid glue may make part removal more difficult. You should choose the appropriate glue type based on the filament, printing environment, and other practical conditions. For more details, please refer to the official wiki: Bambu Lab Wiki. When using a scraper to remove prints, make sure to use the correct technique. If the model adheres too tightly to the build plate, apply alcohol to the interface between the model and the plate to reduce adhesion and make removal easier. This helps prevent damage to the model, the build plate, or potential injury to the user caused by excessive force. Increasing heatbed temperature enhances adhesion. Users need to adjust the temperature of the heatbed based on their specific requirements in order to achieve the most suitable level of adhesion. Before auto-leveling, it is necessary to repeatedly rub the nozzle in the special wiping area of the build plate to completely remove any residual material at the tip of the nozzle. The coating in the special-designed wiping area will gradually become worn over time. This is normal and does not affect print quality or nozzle lifetime, so there is no need to worry about any quality issues. Deposition of dust and grease on the build plate decrease adhesion. It is recommended to regularly clean the surface with detergent and water to to maintain best adhesion. Bambu Lab recommends only using Bambu Lab official glue on the Bambu Lab build plates, and can not be held responsible for any damage caused to plates as a result of using third-party glue on build plates. Do not clean the Engineering Plate with Acetone, as it will damage the Engineering Plate surface. Always wait for a few minutes before removing printed models to allow the plate to cool down for easy print removal. This prevents damage to the plate and ensures a long lifetime of the product. Carefully sanding the surface with fine-grit (600 was recommended) sandpaper can help restore adhesion. The latest firmware brings significant improvements to the Bambu Textured PEI Plate calibration using the Micro Lidar, and it is now fully compatible with the automatic calibration process. The Engineering Plate plate is considered a consumable part, which will degrade over time. The warranty will only cover manufacturing defects, not cosmetic damage like scratches, dents, or cracks. Defective sheets upon arrival are the only ones covered by the warranty. Recommended Settings Please note that other slicer settings might need to be adjusted based on the printed model and the filament requirements Materials Heatbed Temperature Glue Stick Required? PLA/PLA-CF/PLA-GF 45~60℃ Glue Stick/Liquid Glue PETG/PETG-CF 60~80℃ Glue Stick/Liquid Glue ABS (not for A1 mini) 90~100℃ Glue Stick/Liquid Glue ASA (not for A1 mini) 90~100℃ Glue Stick/Liquid Glue TPU 35~45℃ Glue Stick/Liquid Glue PVA 45~60℃ Glue Stick/Liquid Glue PC/PC-CF (not for A1 mini) 90~110℃ Glue Stick/Liquid Glue PA/PA-CF/PAHT-CF (not for A1 mini) 90~110℃ Glue Stick/Liquid Glue PET-CF (not for A1 mini) 80~100℃ Glue Stick/Liquid Glue Product Specifications Material Polyester powder + manganese steel Surface Temperature Resistance Up to 120℃ Thickness 0.5mm Usable Print Size P2S-256mm*256mm H2S-350mm*320mm H2D-350mm*320mm Packaging Size P2S-295mm*315mm*13mm H2S-393mm*380mm*15mm H2D-393mm*380mm*15mm Packaging Weight 0.50kg 0.78kg0.78kg
