Solid H59 Brass Block Bar — Precise Dimensions for Machining, Fabrication & DIY When your project demands a metal stock that machines cleanly, holds tight tolerances, and resists corrosion without constant maintenance, finding the right brass block in the exact size you need can be a real challenge. Whether you are a hobbyist machinist, a small workshop fabricator, or a maker building custom hardware, these solid H59 brass rectangular blocks give you a reliable starting point in over 130 size combinations. Each piece is cut from solid H59 brass alloy — a copper-zinc alloy known for its balance of machinability, thermal conductivity, and corrosion resistance. Cross-sections range from 10 × 10 mm (approx. 0.39 × 0.39 in) up to 20 × 50 mm (approx. 0.79 × 1.97 in), with lengths from 10 mm to 200 mm (approx. 0.39 in to 7.87 in). The rectangular prism profile makes it straightforward to clamp, mill, drill, or turn on a lathe without additional prep work. Typical applications include custom standoffs and spacers for electronics enclosures, bearing housings and bushings for small mechanical assemblies, decorative hardware accents for furniture and cabinetry, heat-sink blocks for low-power thermal management, and raw stock for engraving or CNC milling projects requiring a warm gold-toned metal finish. 🔧 Compatibility: Suitable for standard milling machines, lathes, drill presses, and hand tools. Compatible with common cutting fluids and lubricants used for non-ferrous metals. Works with most soldering, brazing, and silver-soldering processes. ✅ Key Features of These Solid H59 Brass Rectangular Blocks 🟡 H59 Brass Alloy Composition H59 is a copper-zinc brass alloy with copper content typically in the 57–60% range, offering a practical balance of strength, ductility, and machinability suited to general engineering and decorative applications. 📐 130+ Size Combinations Choose from widths of 10, 12, 15, or 20 mm; heights from 10 to 50 mm; and lengths from 10 to 200 mm — so you can select the closest stock size to your finished dimension and minimize waste. ⚙️ Rectangular Prism Profile The flat, square-edged profile clamps securely in a vise or fixture without rounding, making it straightforward to machine parallel faces, drill through-holes, or tap threads. 🌡️ Good Thermal Conductivity Brass conducts heat more effectively than steel, making these blocks useful as small heat-spreader blocks, thermal interface components, or conductive spacers in low-power electronic assemblies. 🛡️ Corrosion-Resistant Surface H59 brass forms a stable oxide layer that resists moisture and mild chemical exposure, reducing the need for protective coatings in indoor and sheltered outdoor applications. ✂️ Ready-to-Machine Stock Supplied with a saw-cut or milled finish. No additional annealing or stress-relief is typically required for standard hobby and light-industrial machining operations. 📐 Technical Specifications — Solid Brass Rectangular Block Bar Material H59 Brass (Copper-Zinc Alloy) Shape Rectangular Prism (Block / Bar) Width Range 10 mm – 20 mm (approx. 0.39 in – 0.79 in) Height Range 10 mm – 50 mm (approx. 0.39 in – 1.97 in) Length Range 10 mm – 200 mm (approx. 0.39 in – 7.87 in) Surface Finish Saw-cut / milled (as-cut) Hardness See variant options Tensile Strength See variant options Thermal Conductivity Approx. 100–120 W/(m·K) (typical for H59 brass) System of Measurement Metric Quantity per Order 1 Pcs (except 10×10×10mm: 2 Pcs) ❓ Frequently Asked Questions How do I choose the right size brass block for my project? Start with your finished part dimensions and add machining allowance — typically 1–3 mm per face for milling or turning. Select the smallest stock size that still gives you enough material to clean up all surfaces. For example, if your finished part is 18 × 28 × 90 mm, a 20 × 30 × 100 mm block is a practical choice. Use the Size selector above to find the combination closest to your needs. Is H59 brass strong enough for structural or load-bearing parts? H59 brass has moderate tensile strength suitable for light-duty mechanical components such as spacers, standoffs, bushings, and small brackets. It is not recommended for high-stress structural applications where steel or bronze alloys would be more appropriate. For decorative hardware, enclosure components, and low-load mechanical parts, H59 brass performs reliably. Will these brass blocks rust or corrode over time? Brass does not rust (rust is specific to iron-based metals). H59 brass is resistant to moisture and mild atmospheric corrosion, making it suitable for indoor use and sheltered environments without additional coating. In humid or marine environments, brass may develop a patina (greenish oxidation) over time, which can be removed with brass polish or left as a natural finish depending on your preference. Can I solder or braze these brass blocks? Yes. H59 brass is compatible with soft soldering (using rosin-core or acid-core solder), silver soldering, and brazing. Ensure the surface is clean and free of oils before joining. Use an appropriate flux for brass to prevent oxidation during heating. Avoid overheating, as excessive heat can cause zinc fuming from the alloy. What tools do I need to machine these brass blocks at home? Brass is one of the more forgiving metals for hobby machining. A benchtop mini-lathe or small milling machine handles H59 brass well with standard HSS (high-speed steel) or carbide tooling. For drilling, standard twist drills work without special coatings. Use cutting fluid or light oil to extend tool life and improve surface finish. A hacksaw or angle grinder with a metal-cutting disc can be used for rough cutting if a bandsaw is not available. Are these blocks compatible with CNC milling or engraving machines? Yes. H59 brass machines cleanly on CNC routers and milling machines equipped with appropriate end mills for non-ferrous metals. Recommended spindle speeds and feed rates vary by machine and tool diameter — consult your tooling manufacturer's guidelines for brass. The flat, parallel faces of these rectangular blocks make fixturing straightforward on a CNC table. What is the difference between H59 brass and other brass grades like H62 or C360? H59 brass contains approximately 57–60% copper and is a general-purpose alloy with good machinability and moderate corrosion resistance. H62 brass has a slightly higher copper content (around 60–63%), offering marginally better corrosion resistance and a slightly warmer color. C360 (free-machining brass) is a leaded brass grade optimized for high-speed machining with excellent chip-breaking characteristics. For most DIY and light-engineering applications, H59 is a cost-effective and practical choice. 🛒 Select your Size (Width × Height × Length) above, then add to cart. { "@context": "https://schema.org", "@type": "FAQPage", "mainEntity": [ { "@type": "Question", "name": "How do I choose the right size brass block for my project?", "acceptedAnswer": { "@type": "Answer", "text": "Start with your finished part dimensions and add machining allowance — typically 1–3 mm per face for milling or turning. Select the smallest stock size that still gives you enough material to clean up all surfaces. Use the Size selector to find the combination closest to your needs." } }, { "@type": "Question", "name": "Is H59 brass strong enough for structural or load-bearing parts?", "acceptedAnswer": { "@type": "Answer", "text": "H59 brass has moderate tensile strength suitable for light-duty mechanical components such as spacers, standoffs, bushings, and small brackets. It is not recommended for high-stress structural applications." } }, { "@type": "Question", "name": "Will these brass blocks rust or corrode over time?", "acceptedAnswer": { "@type": "Answer", "text": "Brass does not rust. H59 brass is resistant to moisture and mild atmospheric corrosion. In humid environments, brass may develop a patina over time, which can be removed with brass polish or left as a natural finish." } }, { "@type": "Question", "name": "Can I solder or braze these brass blocks?", "acceptedAnswer": { "@type": "Answer", "text": "Yes. H59 brass is compatible with soft soldering, silver soldering, and brazing. Ensure the surface is clean and use an appropriate flux for brass. Avoid overheating to prevent zinc fuming." } }, { "@type": "Question", "name": "What tools do I need to machine these brass blocks at home?", "acceptedAnswer": { "@type": "Answer", "text": "A benchtop mini-lathe or small milling machine handles H59 brass well with standard HSS or carbide tooling. Standard twist drills work for drilling. Use cutting fluid or light oil to extend tool life." } }, { "@type": "Question", "name": "Are these blocks compatible with CNC milling or engraving machines?", "acceptedAnswer": { "@type": "Answer", "text": "Yes. H59 brass machines cleanly on CNC routers and milling machines with appropriate end mills for non-ferrous metals. The flat, parallel faces make fixturing straightforward on a CNC table." } }, { "@type": "Question", "name": "What is the difference between H59 brass and other brass grades like H62 or C360?", "acceptedAnswer": { "@type": "Answer", "text": "H59 brass contains approximately 57–60% copper and is a general-purpose alloy with good machinability and moderate corrosion resistance. H62 has slightly higher copper content. C360 is a leaded brass optimized for high-speed machining. For most DIY and light-engineering applications, H59 is a cost-effective choice." } } ] }
Related
Related
Related
Related