HYBRID-MICRO · Feed Systems & Loading A matching, loading, feedpoint, transformer, choke, or antenna-interface component. Why operators make room for it Turn a collection of parts into a deliberate RF system The most visible part of an antenna is rarely the part doing the matching, loading, or current control that makes the deployment usable. That is where CHA HYBRID-MICRO enters the kit. The HYBRID-MICRO Antenna is a lightweight highly portable broadband antenna system designed to offer maximum portability and performance. The antenna weights about 1 lb. That gives the operator a controlled way to shape the completed antenna, verify the match at low power, and understand which component limit governs before transmitting harder. Quick product reference Key Specifications Product type Feed Systems & Loading Primary role A matching, loading, feedpoint, transformer, choke, or antenna-interface component. Available size NO WIRE 30 FT. with 3/8" Connectors 60 FT. with 3/8" Connectors 130 FT. with 3/8" Connectors Frequency 6M - 160M Power 100W SSB PHONE, 25W CW, 25W HIGH DUTY CYCLE DIGITAL MODES (5:1 UNUN) Mounting Configuration 3/8-24 Thread Rf Connection UHF Plug (PL-259) Swr Subject to frequency and configuration, but within limits of most antenna tuners or couplers Length o Antenna Wire: 30, 60, or 130 ft Weight o CHA HYBRID MINI: 1.5 lbs. o CHA HYBRID MICRO: 1 lbs Personnel Requirements And Setup Time one operator, less than 15 minutes (antenna wire), less than 5 minutes (whip). CHA HYBRID - MINI / MICRO Published package contents 1 X HYBRID-MICRO Matching Unit Base 1 X 30',60', or 130' Tinned Copper KEVLAR PTFE (Teflon) (-70°C to 150°C) wire 1X Line Winder Stainless Steel Hardware System requirement Use only in a documented antenna configuration Power rule Observe the lowest published rating of every connected component Operator decision support Plan the complete setup See what this product is best suited for, what the documented setup needs, and the boundaries to confirm before deployment. Best for The most visible part of an antenna is rarely the part doing the matching, loading, or current control that makes the deployment usable. What’s included 1 X HYBRID-MICRO Matching Unit Base 1 X 30',60', or 130' Tinned Copper KEVLAR PTFE (Teflon) (-70°C to 150°C) wire 1X Line Winder Stainless Steel Hardware What else you need A wide-range antenna tuner or coupler is required for the documented configurations Limitations Observe the lowest published rating of every connected component The antenna will operate from 1.8 - 54 MHz (including 160m – 6m amateur bands) without any adjustment with a wide range antenna tuner (the shortest configurations have limited performance below 3.5 MHz). Carefully roll (do not twist) the Coaxial Cable. We recommend that you do not disassemble the CHA CAP HAT. Replace assemblies that do not pass a continuity check. Expansion options CHA MIL WHIP 2.0 CHA MIL EXT 2.0 CHA SS 17 CHA SPIKE MOUNT CHA Jaw Mount Capacity Hat Counterpoise Kit 50’ Paracord and Line Winder Assembly Official product documents Document status: available from current Shopify product record Controlled manufacturer archive: HYBRID_Manual.pdf · match confidence: high. Open documentOpen product handbook What an operator can do Install the component at the documented feedpoint, loading position, or common-mode control location. Observe the lowest published power rating of every connected component and the duty-cycle limits for the operating mode. Verify resonance, SWR, tuner range, connector type, and grounding or counterpoise requirements before transmitting. Compatibility: Physical fit does not by itself establish RF, power, environmental, or structural approval. Follow a documented completed-system configuration.Complete product details The HYBRID-MICRO Antenna is a lightweight highly portable broadband antenna system designed to offer maximum portability and performance. The antenna weights about 1 lb. The antenna will operate at all frequencies in the 1.8-54 MHz band without any adjustment with most modern external antenna tuners. No masts or guying are required. The antenna will work successfully supported by trees, masts, the tops of vehicles or any convenient object or structure. The antenna works most effectively when elevated at a reasonable height. Specifications: Frequency: 6M - 160M Power: 100W SSB PHONE, 25W CW, 25W HIGH DUTY CYCLE DIGITAL MODES (5:1 UNUN) Mounting Configuration: 3/8-24 Thread The Antenna Kit Consists of: 1 X HYBRID-MICRO Matching Unit Base 1 X 30',60', or 130' Tinned Copper KEVLAR PTFE (Teflon) (-70°C to 150°C) wire 1X Line Winder Stainless Steel Hardware ***
