HYBRID-MINI · Feed Systems & Loading A matching, loading, feedpoint, transformer, choke, or antenna-interface component. Why operators make room for it Turn a collection of parts into a deliberate RF system The most visible part of an antenna is rarely the part doing the matching, loading, or current control that makes the deployment usable. That is where CHA HYBRID-MINI enters the kit. The HYBRID SERIES Base is designed to enhance the capabilities of the common HF radio application by allowing faster tuning operation across the HF bands including MARS/CAP frequencies. This Hybrid-Mini Antenna base has an integral broadband impedance matching network (transformer 5:1) allowing broadband antenna tuning. An external antenna tuner is required to provide a low VSWR. The unit is water resistant. That gives the operator a controlled way to shape the completed antenna, verify the match at low power, and understand which component limit governs before transmitting harder. Quick product reference Key Specifications Product type Feed Systems & Loading Primary role A matching, loading, feedpoint, transformer, choke, or antenna-interface component. Available size NO WIRE 3O FT. with 3/8" Connectors 6O FT. with 3/8" Connectors 13O FT. with 3/8" Connectors Available connector type SO-239 BNC Frequency 6M - 160M Power 500W SSB PHONE, 100W CW, 50W HIGH DUTY CYCLE DIGITAL MODES (5:1 UNUN) Mounting Configuration 3/8-24 Thread Rf Connection UHF Plug (PL-259) Swr Subject to frequency and configuration, but within limits of most antenna tuners or couplers Length o Antenna Wire: 30, 60, or 130 ft Weight o CHA HYBRID MINI: 1.5 lbs. o CHA HYBRID MICRO: 1 lbs Personnel Requirements And Setup Time one operator, less than 15 minutes (antenna wire), less than 5 minutes (whip). CHA HYBRID - MINI / MICRO Published package contents 1 X HYBRID Matching Unit Base 1 X 30’ or 60' Tinned Copper KEVLAR PTFE (Teflon) (-70°C to 150°C) wire Stainless Steel Hardware System requirement Use only in a documented antenna configuration Operator decision support Plan the complete setup See what this product is best suited for, what the documented setup needs, and the boundaries to confirm before deployment. Best for The most visible part of an antenna is rarely the part doing the matching, loading, or current control that makes the deployment usable. What’s included 1 X HYBRID Matching Unit Base 1 X 30’ or 60' Tinned Copper KEVLAR PTFE (Teflon) (-70°C to 150°C) wire Stainless Steel Hardware What else you need A wide-range antenna tuner or coupler is required for the documented configurations Limitations The antenna will operate from 1.8 - 54 MHz (including 160m – 6m amateur bands) without any adjustment with a wide range antenna tuner (the shortest configurations have limited performance below 3.5 MHz). Carefully roll (do not twist) the Coaxial Cable. We recommend that you do not disassemble the CHA CAP HAT. Replace assemblies that do not pass a continuity check. Expansion options CHA MIL WHIP 2.0 CHA MIL EXT 2.0 CHA SS 17 CHA SPIKE MOUNT CHA Jaw Mount Capacity Hat Counterpoise Kit 50’ Paracord and Line Winder Assembly Official product documents Document status: available from current Shopify product record Controlled manufacturer archive: HYBRID_Manual.pdf · match confidence: high. Open documentOpen product handbook What an operator can do Install the component at the documented feedpoint, loading position, or common-mode control location. Observe the lowest published power rating of every connected component and the duty-cycle limits for the operating mode. Verify resonance, SWR, tuner range, connector type, and grounding or counterpoise requirements before transmitting. Compatibility: Physical fit does not by itself establish RF, power, environmental, or structural approval. Follow a documented completed-system configuration.Complete product details The HYBRID SERIES Base is designed to enhance the capabilities of the common HF radio application by allowing faster tuning operation across the HF bands including MARS/CAP frequencies. This Hybrid-Mini Antenna base has an integral broadband impedance matching network (transformer 5:1) allowing broadband antenna tuning. An external antenna tuner is required to provide a low VSWR. The unit is water resistant. Specifications: Frequency: 6M - 160M Power: 500W SSB PHONE, 100W CW, 50W HIGH DUTY CYCLE DIGITAL MODES (5:1 UNUN) Mounting Configuration: 3/8-24 Thread The Antenna Kit Consists of: 1 X HYBRID Matching Unit Base 1 X 30’ or 60' Tinned Copper KEVLAR PTFE (Teflon) (-70°C to 150°C) wire Stainless Steel Hardware *** Our blemished products are fully functional, they just didn't meet our high standards. They are a great product at a discounted price for someone who doesn't mind a slight imperfection. WE DO NOT ACCEPT RETURNS ON BLEMISHED PRODUCTS.
Related
Related
Related