The Challenger 10313 lift adapter is the direct replacement for the Challenger lift it came off of. This is the genuine Challenger part — same fit and same working specification as the one already on your lift. Ordering the Challenger lift adapter from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same. Specifications Part number: 10313 Brand: Challenger Type: Genuine OEM lift adapter Fits: CL10, CLFP9, VLE10 These parts wear from repetition and from abuse. A pad that lifts twenty cars a day compresses and tears far sooner than one that works part-time. But abuse ages them faster than hours ever will: an adapter dropped and bent, an arm hit by a car pulling out, a carriage overloaded past its rating. Rubber pads are consumables that need regular replacement; steel parts last until something bends or cracks them. What lifts this lift adapter fits This lift adapter fits the lift models below. Click a model to open its visual parts breakdown — the exploded drawing with every part numbered, so you can confirm this is the right part for your exact lift before you order. CL10 — see the exploded parts breakdown for this lift CLFP9 — see the exploded parts breakdown for this lift VLE10 — see the exploded parts breakdown for this lift Replacing your lift adapter Replacing column hardware — anchors, arm-pin retainers, slide blocks, fasteners — is about restoring the tight, no-play fit the structure was built with. Use the correct grade and torque, and confirm the column sits flat and solid to the floor afterward. The complete procedure lays out what to check and in what order. Not sure on the procedure? Find your lift in our parts lookup or call and we will walk you through it. Find the right part for your lift Want to be sure before you buy? Pull the model and serial off your lift's plate and open our Challenger parts lookup to open the exploded parts breakdown for your model — find your part on the drawing and you know it fits. New to finding your model number? our guide to finding your model number covers it, or send a photo of the plate and we will read it for you. Signs this part is worn out Check the arms for straightness and the pins for wear. Sight down each arm for a bend from being backed into or overloaded, and check that the telescoping sections slide without excessive slop. Worn arm pins and retainers let the arm lift or rotate under load. An arm that's bent, or that flops on a worn pin, isn't holding the car where you set it. Parts commonly replaced at the same time Smart to replace the group: contact points wear together, so pads, adapters, and their pins are best done in one pass. It keeps the lift level and the vehicle secure. We will build the matched structural kit for your model so you are not chasing one worn pad at a time. Safety notes Structural wear sneaks up: a pad flattens, a hole elongates, a ramp lip curls, and one day the vehicle is not sitting where it should. Treat these as safety parts, not cosmetics. Replace them before they let a load shift, and confirm every mounting point is tight and true before the lift carries weight. Before you order Before ordering, confirm your lift's model and serial and check how many of the part you need — pads and adapters usually go in sets of four, and replacing one worn one still leaves three worn. Match the old part's shape and mounting against what you order, and call if the fit is not obvious. Not sure this fits? Here's how to check Pull the number off your lift's model plate first — model and serial both. Manufacturers run mid-cycle revisions that keep the model name but change hardware, so two lifts with the same name on the column can take different parts. The serial is what removes the guesswork. Second check: compare the old part against this listing before you order. Length, mounting pattern, and thread sizes tell most of the story. If anything doesn't line up, or if the old part is too worn or broken to measure, call us with photos — we work on these lifts every week and can usually confirm fit from a picture and the lift's serial faster than you can dig through a parts diagram. Why buy your Challenger lift adapter from Auto Lift Services We install, inspect, and repair Challenger lifts every week — the 10313 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.
