CHEM-THANE P-50/100/Flex Viscosity Reducer Available Sizes 1 Gallon 5 Gallons Description CHEM-THANE P-50/100/Flex Viscosity Reducer is a field additive designed for use with CHEM-THANE P-50, P-100 and P-Flex; ROCKTRED’s modified aliphatic / polyaspartic high performance coatings. Uses CHEM-THANE P-50/100/Flex Viscosity Reducer aids in ease of application when using CHEM-THANE P-50, P-100 or P-Flex by lowering the mixed viscosity of the material and allowing for higher coverage rates. When at least 10 oz. of the Viscosity Reducer is added to CHEM-THANE P-100 it becomes a self-priming coating. Viscosity Reducer is not required in CHEM-THANE P-50 when used as a primer. CHEM-THANE P-FLEX is not recommended for use directly to concrete. Loading Ratio CHEM-THANE P-50/100/Flex Viscosity Reducer is to be used only with CHEM-THANE P-50, P-100 or P-Flex. Do not exceed the following maximum loading of Reducer per mixed gallon of product. CHEM-THANE P-50 6 oz. Reducer/Mixed Gal. Maximum CHEM-THANE P-100 16 oz. Reducer/Mixed Gal. Maximum CHEM-THANE P-Flex 12 oz. Reducer/Mixed Gal. Maximum You may use less than the maximum loading rate to fine tune the mixed viscosity per the job needs. Advantages Packaged as a field additive to provide applicator control over finished mixed viscosity of product. Using Viscosity Reducer will not alter the high-performance physical properties such as UV and chemical resistance, flexibility and abrasion resistance. Will increase the flow, leveling and coverage rate of the product. Use will allow CHEM-THANE P-100 to be applied as a primer. CHEM-THANE P-50/P-100 Viscosity Reducer is made from VOC exempt, low odor materials. Using the Viscosity Reducer will NOT increase reportable VOC or HAPS. Only a slight odor increases results when used at the maximum loading ratio. Limitations & For Best Results Do not use more than 16 oz. of Viscosity Reducer per mixed gallon of CHEM-THANE P- 100. Do not use more than 6 oz. of Viscosity Reducer per mixed gallon of CHEM-THANE P- 50. Do not use more than 12 oz. of Viscosity Reducer per mixed gallon of CHEM-THANE PFlex. When applying CHEM-THANE P-100 directly to concrete add a minimum of 10 oz. Viscosity Reducer per mixed gallon of P-100. Using Viscosity Reducer in pigmented CHEMTHANE P-50, P-100 or P-Flex will result in less than normal hiding. Keep away from open flame and ignition sources. Product Application Add CHEM-THANE P-50/100/Flex Viscosity Reducer to the resin component of the product, mix slowly by hand or at very low RPM for 30 seconds until incorporated. Proceed to add colorant if needed and mix until homogenous. Add Hardener and follow standard mixing and application instructions. Product Storage DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50° F. Disposal Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations. Important Notice Always read and acquaint yourself with ROCK-TRED’s Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty.
