Based on the principles of the dbx Zone Processing products, the SC 64 Digital Matrix Processor is the new flagship product for Digital Matrix Processing. Wizard driven configuration using HiQnet System Architect™ makes unprecedented DSP power, incredible routing flexibility and a rich palette of processing tools accessible with the minimum of training. The SC 64 represents the professional choice of foundation on which to build even the most demanding integrated system. Features 64 channels of analog I/O configurable in banks of 8 8 Mic/Line and Phantom Power per channel on Analog Input Cards Ethernet / Serial Control High Speed Option Slots Control Inputs and Logic Outputs Pre-configured Architecture Selectable DSP inserts on inputs and outputs including Advanced Feedback Suppression (AFS™), Automatic Gain Compensation (AGC), Compression, De-Essing and Notch Parametric Equalization Complete routing flexibility Comprehensive configuration, control and monitoring from HiQnet System Architect™ Wizard Configuration Events Scheduler Optional Media Engine for media playback Optional ZC wall panel control Specifications Indicators Per Input: Signal Present, Clip, 48V Phantom Power, SYNC, I/O card type (IN, OUT, D-IN, D-OUT) Other Indicators LCD Display, Page Button, Select Button and LED indicators for: Global CLIP, Link/Active, RS-232 and Power Audio Card Slots 8 Card Slots (A, B, C, D, E, F, G, H) High Speed Option Slot 2 Card Slots Input (8) per Input Card Input Connectors Phoenix/Combicon, 3.5mm pitch Input Gain Range Nominal Gain 0 dB, electronically switchable up to +48 dB, in 6 dB steps Input Type Electronically balanced, RF filtered Input Impedance 3.5 k ohm Max Input +22dBu CMRR >40 dB typical, >55 dB at 1 kHz Mic Preamp Phantom Power +48 VDC, selectable per input Output (8) per Output Card Output Connectors Phoenix/Combicon, 3.5mm pitch Output Type Electronically balanced, RF filtered Output Impedance 44 Ω Max Output +20 dBu Dynamic Range 107 dB unweighted, 110 dB A-weighted Internal Processing 32 bit floating point THD+Noise 0.0045% typical at 0 dBu, 1 kHz, 0 dB input gain Frequency Response 20 Hz- 20 kHz, +/-0.50 dB Sample Rate 48kHz GPIO Ports 8 Control Inputs and 6 Logic Outputs (Phoenix/Combicon, 3.5mm pitch) Control Input Voltage 0 to 4.5v Control Input Impedance 4.7 k ohm to +5V (2-wire mode) Logic Output Voltage 0 or +5V unloaded Logic Output Impedance 440 ohm Logic Output Current 10mA source, 60mA sink Relay Contact Connector Phoenix/Combicon, 3.5mm pitch Relay Contacts Common (C), Normally Open (NO), Normally Closed (NC) Relay Contact Rated Load 0.3A at 125VAC, 1A at 30VDC Watchdog Output Phoenix/Combicon, 3.5mm pitch for failsafe control Opto-isolated Watchdog Output Current 14mA maximum Watchdog WIthstanding Voltage 80V maximum (Off) Watchdog Series Impedance 220Ω (isolated) Input Delay Length per channel: Up to 5120ms of input delay Input EQ per channel: 4 Band Parametric Input Gate per channel: Downward Expander Input Signal Processing Two selectable Input Processing blocks per input Insert Types Advanced Feedback Suppression, Automatic Gain Control, Compressor, De-Esser, 12-Band Notch EQ, 12-Band Parametric EQ, Sub-Harmonic Synthesizer Ducker 24 level priority ducker Routing/Mixing 32x1 mixer on every output zone Output Insert Processing One selectable Output Processing block per output: Gain, Automatic Gain Control, Ambient Noise Compensation, Auto-Warmth™ Crossover configs: 1x1, 1x2, 1x3, 1x4 Crossover Filter Type Bessel 6, 12, 18 and 24 dB/Octave, Butterworth 6, 12, 18 and 24 dB/Octave, Linkwitz-Riley 12 and 24 dB/Octave Output EQ 6 Band Parametric per channel Limiter Type dbx PeakStopPlus™ Output Delay Length Up to 5120ms of output delay Controls Ethernet, RS-232, Optional dbx ZC Wall Panels Power Consumption 100V to 240VAC 50/60Hz, 120 Watts Dimensions 3.5" (2U) x 19" x 15" (89mm x 483mm x 381mm) Unit Weight 18.9 lbs. / 8.57 kgs. (with all audio cards installed)
