Description of DDCS4 V3.1 Offline CNC Controller DDCS V3.1 is 4 axis motion controller for stepper and servo systems. DDCS V3.1 numerical control system adopts the ARM+FPGA design framework. ARM controls the human-computer interface and code analysis and the FPGA provides the underlying algorithms and creates the control pulse. This guarantees reliable control and easy operation. The internal operating system is Linux based. The panel layout structure of the CR8-500 is very rational to save space. All operations are controlled by only 17 keys and a comprehensive G code set is supported. Specifications: 16 opto isolated digital inputs,3 opto isolated digital outputs; Upgrade algorithm,support soft interpolation,fixed arc interpolation bug of the old version; Analog spindle control 0-10V spindle control (can be modified as PWM output); 3-4 axis motor Control.Differential Pulse and direction output signal,Max.500Khz per axis; ARM9 main control chip,FPGA core algorithm chip; 5 inches TFT screen, resolution ratio: 480×272,17 operation keys; 24VDC power input, minimum Current is 0.5A; USB flash disk support for Gcode file input,no size limite of the G-code file; 1GB internal memory; Support standard MPG; Jog function for each axis (continuous, step, defined distance); Support the operation of quickly specify the running position; Support for “Power Cut” recovery. Data is automatically saved; Support the origin and Limit share the same Input ports; The controller only support NPN type limited switch. Appearance and Size: Explanation of Abbreviations When operating the DDCS, the users will come across some English abbreviations.The letters of the abbreviation stand for: FRO: Feed Rate Override SRO: Spindle Rate Override SRJ: Jog Speed Setting F: Feed rate, unit is mm/min S: Spindle Speed, unit rev/min. X: The coordinate code of the X axis. Y: The coordinate code of the Y axis. Z: The coordinate code of the Z axis. A: The coordinate code of the A axis BUSY: The system is busy. You still can adjust FRO and SRO READY: READY mode, any operation can be done RESET: Reset mode, controller is in “OFF” mode, no operation can be performed CONT: Continuous mode, each axis can be manually jogged with the arrow keys Step:Manual Step Mode，each axis can be jogged in defined steps MPG: MPG mode. Operate the machine with the MPG (Manual Pulse Generator) AUTO: Run G code. Auto is showing when file is processing Details of 57HSE3N 3Nm Motor Motor model: 57HSE3N Motor current: 3.5A Output torque: 3N.m Body length: about 132MM Shaft diameter: 8MM, no keyway Outletmode: single output shaft Rated speed: 1000 rpm (no-load speed: 2000 rpm) Outlet mode: two-phase four-wire (must be wired according to motor label) Details of Stepper Drive HBS57 Drive Model: HBS57 (Nema 23, for 57 stepper motor) Pulse Signal: 3.3V/5V/24V compatible. No string resistor required Voltage Range: DC16-70V (New Version: DC24-80, send in random) Subdivision Setting: 800-51200 subdivision The new 32-bit DSP digital 57 closed-loop stepper motor driver, engraving machine, CNC equipment available. PWM current control, low noise, high speed torque is 40% larger than ordinary drives. Mean Well Power Supply + Cable + Signal Mean Well Power Supply 36V 600W Output Voltage-Channel: 36V Output Power: 597.6W Enclosed Case Input Voltage: 90 VAC ~ 132 VAC/180 VAC ~ 264 VAC selected by switch, 254~ 370 VDC Output Current-Channel: 0~16.6A Input Frequency: 47 Hz to 63 Hz Mounting Style: Chassis Length: 247 mm Width: 127 mm Height: 63.5 mm Mean Well Power Supply - 24V 35W Output Voltage-Channel: 24V Output Power: 36W Enclosed Case Input Voltage: 85VAC to 264VAC, 120VDC to 373VDC Output Current-Channel: 1.5A Mounting Style: Chassis Length: 99mm Width: 82 mm Height: 30mm Input Frequency: 47Hz to 63Hz Unit Weight: 230g Cables 1x 2 core DC cable for motor driver to power supply (Z-Axis) 1x 4 core shielded cable (Z-Axis Driver Signal) 3x 4 core shielded cable (X,Y,A Driver Signal) 3x 2 core DC cable for motor driver to power supply (X,Y,A) 1x 4 Pin EDG through wall connectors 1x 6 Pin EDG through wall connectors 3x 2 core DC cable for E-Stop Switch and controller 3x 2 core shielded cable (X,Y,Z). 1x 12 Row Screw Terminal Block 1x Single Core Hook Up wire. (Black) Limit Switch Kits 3 x Micro Limit Switch 3 x Limit Switch Plate 6 x M3 10mm Cap Head Screw 6 x M5 8mm Cap Head Screw 3 x M5 Drop-in Tee Nut NOTE:The holes in the switch will need to be opened a little (3mm drill bit) to allow for the M3 screw or alternatively you can use a M3 tap to cut a thread into the plastic E-stop Switch Max Current: 10A Max Voltage AC 660V Rated Load: AC: 220VAC/6A, 380VAC/4A, 660VAC/2A DC: 440VDC/0.3A,220VDC/0.5A, 110VDC/1A TYPE: N/C Withstand Voltage: 2500V /60S Temperature: -25°~+55° Contact resistance:
Related
Related
Related
Related