SMD6 — Double-Sided Cantilever Rack Starter Kit (6') Already have this starter unit? View the matching AMD6 Double-Sided Cantilever Rack Add-On Kit → The SMD6 is a Series 1000 Medium Duty double-sided cantilever rack starter kit that stores materials on both sides of the upright — delivering twice the storage density of a single-sided unit in the same floor footprint. At 6' tall with 12" arms and 12 total storage positions (6 per side), it's built for free-standing aisle installations where you need to load from both directions.Ships complete with 2 uprights, 12 straight arms, and a brace set. Arms adjust on 3" centers. What's Included 2 uprights (6' height, 54" base length) 12 straight arms (12" length, 1,000 lb capacity each) 1 brace set (47" length) All hardware for assembly Why the SMD6 Double the storage, same floor footprint — Arms extend from both sides of the upright, allowing you to store and access materials from two aisles simultaneously — without using any additional floor space versus a single-sided unit.Highest total capacity in the 6' medium duty lineup — At 16,200 lb total upright capacity, the SMD6 stores significantly more than its single-sided counterpart while maintaining the same compact 6' height.Grows with your operation — Add AMD6 add-on units at any time to extend into a continuous double-sided row system using shared upright frames.Forklift accessible from both aisles — Open design on both sides allows forklift loading and unloading from either direction, improving traffic flow in high-throughput storage areas. Questions before ordering? Call (929) 577-4339 or email [email protected]. Floor Anchors (Required, Not Included): Uprights must be anchored to the floor before use. MECO recommends a minimum of 2 anchors per base — 1 in the front and 1 in the back on opposite sides of the base. Each base has holes for up to 4 anchors. Recommended anchor spec: ½" × 4¼". Anchors are not sold by MECO and must be sourced independently. Building codes vary by location — consult local codes for specific requirements. Series 1000 Medium Duty Double-sided Starter Units — Model Comparison Model Height Arm Length Arms Included Arm Capacity Total Capacity Unit Weight SMD6 (this model) 6' 12" 12 1,000 lb 16,200 lb 296 lb SMD8 8' 24" 16 600 lb 10,600 lb 387 lb SMD10 10' 36" 24 400 lb 7,600 lb 617 lb Arm capacity decreases at greater heights and arm lengths due to increased bending load on the upright column — a standard cantilever rack engineering characteristic. All capacities are per MECO Omaha specifications based on evenly distributed loads. Need single-sided storage? See the SM6, SM8, SM10 single-sided starter units. Specifications Specification Detail Series Series 1000 Medium Duty Configuration Double-sided Upright Height 6' (72") Base Length 54" Arm Length 12" Arm Capacity 1,000 lb per arm (evenly distributed load) Total Upright Capacity 16,200 lb Number of Arms 12 Brace Set Length 47" Unit Weight 296 lb Arm Adjustability 3" centers Standard Color Gray Add-On Unit AMD6 Double-sided Cantilever Rack Add-On Kit Important: Capacities are based on evenly distributed loads. Unit must be anchored to the floor per assembly instructions. Customization Options Arm Lips (L Suffix) Bolt-on 2" arm lips are available for all 12 MECO cantilever rack SKUs in this lineup, including this model. Lips extend 2" above the arm surface and are used to retain cylindrical loads — pipe, tubing, round bar — that may otherwise roll off the end of the arm. Applies to both arms and bases — lips bolt on to every arm and base in the unit No extra charge if ordered with the rack — add the "L" suffix to the model number at time of purchase (e.g. SM6 → SM6L) and lips are included at the same price Can be ordered separately later — lips can be field-installed at any time after purchase, though a separate order and charge will apply Non-structural — lips are a retention feature only and are not intended to bear any portion of the load Factory punched — all MECO arms are factory punched to accept bolt-on lips, so no drilling is required To order with lips, contact us at [email protected] or (929) 577-4339 and we will place the order with the L suffix at no additional cost. Additional Customization Options Contact us to discuss any of the following configurations: Inclined Arms — For cylindrical loads that tend to roll, inclined arms pitch at 20° (approximately 4.36" per foot) to keep material secure on the rack. Bolt-On Pipe Sockets — Field-installable pipe sockets (1⅜" inside diameter) provide an additional stop at the end of the arm for round stock and tubing. Drop-In Deck Support Saddles — Convert the SMD6 to a decked system for storing boxes, cartons, or furniture. Pre-engineered to accommodate 2×4 cross supports. Custom Colors — Available at additional cost. To discuss customization options, call (929) 577-4339 or email [email protected]. Shipping & Returns Shipping Policy This product ships as industrial freight via motor carrier from Omaha, NE. A forklift or suitable lifting device is required to unload — standard liftgate service is not available. Freight is calculated based on your location and order size. Contact us before ordering for a freight quote specific to your facility. Estimated lead times based on total order value: Order Value Lead Time $0 – $1,000 1–2 weeks $1,001 – $5,000 2–3 weeks $5,001 – $10,000 2–4 weeks $10,001 – $20,000 4–6 weeks $20,001 – $40,000 5–7 weeks $40,001+ 8 weeks Lead times are based on total order value and may vary. Contact us to confirm timing before ordering. If you have a delivery deadline or need to hold shipment until your facility is ready, we can coordinate directly with the supplier. Freight quotes are subject to change without notice. A 3.9% service fee applies to all credit card transactions. Tracking provided via email once your order ships. Return Policy Return Policy Details Return Window 30 days from delivery Condition Required Unused, unassembled, in original packaging with all hardware Restocking Fee 20% Damaged / Missing Items Additional 20% refurbished fee applies Return Shipping Buyer responsible for all return freight costs Special Orders Not returnable for credit To initiate a return, contact us at [email protected] or (929) 577-4339 within 30 days of delivery.
