4055 Kick Drum Microphone DescriptionThis 4055 Kick Drum Microphone has been optimized to pick up the true sound of the kick (bass) drum. This microphone delivers the renowned DPA sound, clarity and linear frequency response, both on axis and off axis. The low frequency response, dynamics and high-level capabilities of this mic are superb and result in a very tight, natural, well-defined sound. Full of highs and lows plus all the mids as well. Features Picks up the clear, true sound of the kick drum Flat frequency response so you can shape the sound your way Built tough to withstand rough use on the live stage Asymmetric design for easy placement inside or outside the kick drum What's in the box 1 4055 Kick Drum Microphone 1 UA0961 Microphone Holder Application GuidePlacement guideThe 4055 Kick Drum Microphone is easy to position both inside and outside the kick drum due to its asymmetrical design. This microphone is very flexible, allowing you to completely transform your sound design, just by moving the microphone or changing its angle. Cleaning guide Keep the microphone dry – away from water and cleaning fluids. Do not use sprays or fluids containing chemicals that could remove static electricity on or near the microphone. This could cause permanent damage.Please note that the capsule is permanently fixed and can’t be changed.The microphone grid is the only part that may be cleaned. To clean the grid properly, without risk of causing damage to the capsule, you have to unscrew it from the microphone body. Be aware that the mic capsule itself should not be cleaned in any way, as it will influence the performance.The grid consists of two parts: the outer black metal mesh and an inner foam windscreen. Both parts may be cleaned separately.All the parts should be assembled again in the opposite order. Be careful to align the foam windscreen in the outer black metal mesh. When remounting, take care to tighten the grid firmly. SpecificationsDirectional pattern Open CardioidPrinciple of operation Pressure gradientCartridge type Pre-polarized condenserFrequency response 20 Hz - 20 kHzEffective frequency range ±2 dB, at 20 cm (7.9 in) 40 Hz - 18 kHz with a 6 dB soft boost at 10 kHzSensitivity, nominal, ±2 dB at 1 kHz 2 mV/Pa; -54 dB re. 1 V/PaEquivalent noise level, A-weighted Typ. 27 dB(A) re. 20 µPa (max. 29 dB(A))Equivalent noise level, ITU-R BS.468-4 Typ. 39 dB (max. 41 dB)Distortion, THD < 1% 156dB SPL RMS, 159 dB SPL peakDynamic range Typ. 132 dBMax. SPL, THD 10% 164 dB SPL peakRated output impedance 380 ΩMinimum load impedance 2 kΩCable drive capability 100 m (328 ft)Output balance principle Impedance balancing with Active DriveCommon mode rejection ratio (CMRR) > 55 dBPower supply (for full performance) P48 (Phantom Power)Current consumption 2.0 mAConnector XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phaseColor Matte blackWeight 241 g (8.5 oz)Microphone diameter 57 mm (2.24 in)Capsule diameter 17 mm (0.67 in)Microphone length 132 mm (5.19 in)Maximum output voltage, RMS 9.75 VPolarity +V at pin 2 for positive sound pressureTemperature range -40°C to 45°C (-40°F to 113°F)Relative humidity (RH) Up to 90%Typical on and off-axis response of a DPA 4055 Kick Drum Microphone measured at 20 cm (7.9 in) Typical directional characteristics of a DPA 4055 Kick Drum Microphone Replacement parts DUA0720B 4055 Microphone Grid, Black UA0961 Microphone Holder KE4055 Zip Case
Related
Related
Related
Related