ELRS 2.4G SERIAL ELRS 2.4G | PLUGS - BMI270 SERIAL ELRS 2.4G | NO PLUGS - BMI270 FRSKY SPI FRSKY | PLUGS- BMI270 SPI FRSKY |NO PLUGS - BMI270 F4 1S 5A AIO Brushless Flight Controller .8MM Thickness The ultralight F4 1S 5A AIO Brushless Flight Controller is back in stock with new and upgraded features. Compared to the previous version, the new board uses Serial ExpressLRS 2.4G instead of SPI ELRS 2.4G so that it can support ExpressLRS V3.0 and also has a Frsky RX version to choose from. We updated the FC with high-quality BMI270 gyro and BB51 ESC hardware. In addition, this new board supports the Betaflight Blackbox function. *** IMPORTANT *** REVIEW LINK *** BETAFPV *** ANNOUNCEMENT *** https://betafpv.com/collections/brushless-flight-controller/products/f4-1s-5a-aio-brushless-flight-controller-elrs-2-4g Betaflight Firmware and CLI F4 1S 5A AIO Brushless Flight Controller comes with the default firmware betaflight_4.3.1_BETAFPVF411 (ELRS) or betaflight_4.2.11_BETAFPVF411RX (Frsky). The default firmware for Serial ExpressLRS 2.4G RX version supports ELRS V2.4 RX. Pay attention, For the Serial ExpressLRS 2.4G version, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyro. For the SPI Frsky version, DO NOT flash the other firmware, otherwise, the RX will be lost in control at a very close range. We have already built our own firmware betaflight_4.2.11_BETAFPVF411RX for SPI Frsky RX version to support BMI270 gyro. Please check the below link to download the firmware. Download the firmware and CLI dump file for the F4 1S 5A FC ELRS/Frsky board. https://support.betafpv.com/hc/en-us/articles/7064243258777-Firmware-for-F4-1S-5A-Flight-Controller-BMI270-ELRS-2-4G-Frsky- Note: The RX RSSI values drop when the flight controller is installed on the quadcopter with HD digital VTX (Walksnail or HDZero). For example, the theoretical failsafe RSSI values for 250Hz packet rate are -108dBm. Actually, the RX will be possibly lost in control when the RX RSSI values reach about -92dBm. Package 1 * F4 1S 5A AIO Brushless Flight Controller (ELRS or Frsky) 4 * M1.2x4mm Screws 4 * M1.4x5mm Screws 4 * Anti-vibration Rubber Dampers 8 * Motor Pin Connectors (Light version included) Flight Controller Warranty Policy At weBLEEDfpv, we are committed to providing high-quality products. However, due to the technical nature of flight controllers and the precision required for installation, our warranty policy for flight controllers is as follows: 1. No Warranty Post-Soldering: Once any soldering has been performed on the flight controller, we are no longer responsible for replacements, repairs, or refunds. The process of soldering can introduce various factors that may lead to damage, and we are unable to control or verify the conditions in which the soldering was conducted. 2. Pre-Soldering Inspection: Before you begin soldering, we recommend carefully inspecting the flight controller for any potential issues. If any defects or issues are found prior to soldering, please contact us immediately for a replacement. 3. User Responsibility: Soldering requires skill and experience, and improper techniques may result in damage to the flight controller, including but not limited to overheating or lifting solder pads. Please ensure you are confident in your soldering abilities before proceeding, as we cannot be held liable for any damages caused during installation. 4. Final Sale: All flight controller sales are final once the product has been modified or soldered. We are unable to offer returns or exchanges on used or modified products.
Related
Related
Related
Related