The Ravaver Gengar Face Toploader Binder is a Pokemon toploader binder wrapped in lavender purple PU leather around 252 side-loading slots sized exactly for standard 3"×4" toploaders. Full-zip closure. Zero metal rings. A stitched Gengar face across the cover—orange eyes locked on you, white grin a little too wide. The same eyes and grin stitched on the back with the Ravaver logo underneath, purple zipper pull at the seam. Your best cards go in. Gengar stays out front. Toploaders are what you reach for when a card stops being just another pull. This is where they go after that. 252 slots, 15.4 inches of lavender leather, and that grin stitched across the front and the back, so it reads either way it lands on a trade table. Set it down. Watch where people look before you've unzipped a thing. Specs Capacity 252 toploaders (28 pages × 9 slots) Fits Standard 3" × 4" toploaders — any TCG or sports card. Not sized for graded slabs Pocket size 3.3" × 4.3" Size 15.4" H × 12.6" W × 2.4" D Cover Stitched Gengar face (front and back) on lavender purple PU leather Closure Full-perimeter zipper Pages Acid-free, PVC-free, side-loading (ClearLock™), ring-free Shipping Free U.S. shipping from Los Angeles Packaging Black Ravaver gift box, ready to give Warranty Free 2-year warranty Key Features: 252-Toploader Capacity: 28 pages, 9 slots each, all cut for standard 3"×4" toploaders. Room for a full ghost-type run plus every VMAX you stopped trusting to a sleeve. Load them side-on, zip it shut, nothing shifts. PSA-Level Protection: Acid-free, PVC-free pages behind a zip that runs the whole perimeter. The standard of care a slab gets, without sending the card away to get it. Ring-Free Build: Nothing metal anywhere inside. No D-rings to press a dent into a corner or crease a holo halfway down the page. Toploaders lie flat, front page to back. ClearLock™ Side-Loading Pockets: Cards load from the side, so a toploader can't back out mid-flip. Clear enough that Gengar's shadow work still reads through two layers of plastic. Cracking-a-Pack Zipper: Full-perimeter zip with a purple pull, and that first tug sounds like opening a fresh pack. Dust stays out. So does whatever gets knocked over at trade night. Acid-Free, PVC-Free Pages: Pull a card out ten years from now and it comes out the way it went in. No yellow film, no tacky pages, no foil stuck to plastic. Stitched Gengar Face Cover: Not an embossed outline. The whole face is stitched into lavender leather panel by panel, orange eyes and that too-wide white grin, thread you can run a thumb across. The eyes and grin carry over to the back alongside the Ravaver logo, so it reads as Gengar whichever way it lands on the table. Who It's For: Best for: toploadered Gengar hits that deserve a binder people notice across the table. For the Gengar collector whose best cards already moved into toploaders and who won't carry something plain while doing it. The embossed Gengar Toploader Binder is the quiet option. This one has the face stitched on both sides, so there's no angle where it reads as a plain purple binder. Bring it to a swap and people clock it before you unzip it. It also ships in a Ravaver gift box, which makes it an easy call for anyone shopping for a Gengar fan who already owns the basics. Backed By Ravaver: Free 2-year warranty on every binder. If something goes wrong, we make it right. No fine print, no chasing receipts. FAQ What size toploaders fit in this binder?Standard 3"×4" toploaders, the most common size for raw Pokemon cards. Slide them in side-loaded, snug fit, no forcing. Will graded slabs fit?No. This binder is built specifically for toploaders, which are thinner than graded slabs. If your card is in a toploader, this is the binder for it. If it's been graded and slabbed, you'll want a binder sized for slabs. Face or embossed—which Gengar Toploader Binder is which?Same 252-toploader build underneath. Same slot count, same ClearLock pockets, same zipper, same warranty. The difference is the cover and the color. The Gengar Toploader Binder is deep purple with his outline pressed into the leather, subtle enough that people notice it after they've already sat down. This one is lavender with the full face stitched on, front and back. Pick based on how much attention you want the binder pulling. Card Binder or Toploader Binder—which do I need for my Gengar collection?Depends where the cards are sitting now. If your Gengars are in sleeves, the Gengar Face Card Binder holds 360 of them in the smaller 13.8" build. Once they've moved up to 3"×4" toploaders, this is the one. The stitched face is on both, so you're really choosing by what's protecting the card, not by the cover. Do toploadered cards from other TCGs fit?Yes. If it's in a standard 3"×4" toploader, it fits. Pokemon, Magic, Yu-Gi-Oh, sports cards — the slots hold the toploader, not the game.
