This is the FULL Tonic RC HCT Kit for the Tamiya Honda City Turbo (car not included). Parts include: Front splitter with mounting posts, hex bolts, 4 neodymium magnets. F1 Rear Wing with hex bolts, nuts, thin nut wrench. Rear Diffuser with mounting posts, bolts. Rear Position Light LED mount with nine 3mm LEDs. Side Skirts (left and right). Roof Scoop (2 pieces). Magnetic body post system with 10 neodymium magnets, hex bolts, nuts. Dashboard/console RHD (stock RIGHT hand drive) with gauge cluster, with 10 white LEDs, center console LED cover in both clear (for sticker) and solid black, hex bolts, nuts. Front roll cage gussets pair (white). Front intercooler (silver). Front tow hook mount with red aluminum hook, hex bolt, nut. Headlights pair (transparent) with two 5mm cool white LEDs. Foglights pair (transparent) with two 5mm cool white LEDs. Optional (4) headlight/foglight 5mm warm white LEDs (for you to personalize). Center mono windshield wiper. License Plates, front and rear (2 Euro and 2 standard sizes included, 4 pieces in total). Tonic RC Sticker Sheet Includes everything in the Exterior Aero Kit, Body Bits Kit, plus Dashboard/console system, rear magnetic system (to work in conjunction with the Splitter magnetic system). Individually priced, these parts would cost $363.00 USD combined. At $175 USD, that's over a 50% discount. If you're using (or planning on using) the Yeah Racing aluminum shock towers, you'll need to order these optional parts for proper fitment! HCT Front Splitter YR Mounting Tubes HCT Rear Diffuser YR Mounting Tubes Tips: Some parts may still have some support tree remnants. Using needle nose pliers can pluck those stray strands off the main part. You can also sand down the parts to make them smooth, but be aware that it may lighten or dull the sanded area as compared to the rest of the part if you don't plan on painting them (I didn't paint any of the black parts and kept them bare). If a bolt needs to get through a stubborn hole, a hole reamer or even a simple hex driver may be all that's needed to make the hole larger for the bolt. Some of the large flat surfaces with speckled/rough texture may have residual hot bed adhesion glue residue still on them. If you want to remove that slightly sticky surface, simply clean it with warm water and a micro dot of dish soap (and a soft green Brillo pad can be used to help get the residue off faster). Note: At this time, I did not create the interior driver plate/mounting/kinematics system (for public release), as shown in my Honda City Turbo Senna Edition video on YouTube (where the driver moves his head and arms). That involved a number of added specialty parts that aren’t cost effective for this kit. I may find a solution at a later date, so please stay tuned. Also noted is that the interior roll cage was created with basic styrene tubing, cut to size, and glued in place, as shown in my Honda City Turbo Senna Edition video on YouTube. This cage is not included, except for the listed front roll bar gussets. The Marlboro/Shell/Honda/Senna decals and livery are not included in this kit, as they were custom made for my personal build. Installations: Please go to each parts' product page to access installation instructions for each part. These instructions are still in development, so please check back for updated instructions. Tech note: Each red LED is 2 volts, 20mA, Anode (+) = longer stem, Cathode (-) = shorter stem. Each white LED is 3 volts, 20mA, Anode (+) = longer stem, Cathode (-) = shorter stem. Attention: Please be advised that the HCT aero parts (splitter, wing, diffuser, side skirts) are more for aesthetics than that of actual performance gains. While they might introduce some small amount of aerodynamic gains, it's unlikely that it would be of significant measure in a race situation. Also be cautious that because these aero parts are somewhat extrusive from the car's body, that it introduces added risk of breakage if it collides with another object or if the car flips over. Like with any RC car, please drive carefully!
