High Opaque Plastisol Ink is our high-pigment plastisol — the same easy printing as All Purpose across all three fabric types (100% cotton, 50/50 blends, and light-color polyester), loaded with extra pigment for bold, one-hit opacity on the darkest garments. It's low-bleed and stretchable, cures at 300–310°F, and prints in 62 colors. CPSIA-compliant and phthalate-free, made in Hackensack, New Jersey. 62 colors. Pint, quart, gallon and 5 gallon. Heat cure. Made in the USA. Also available in larger quantities — 30-gallon and 55-gallon drums; call 201-487-9600 for volume and discount pricing. Features & benefits Extra-high pigment & opacity — bold, one-hit coverage on the darkest garments Prints on all three fabrics — 100% cotton, 50/50 blends, and light-color polyester Low-bleed on light polyester — for dark or 100% poly, underbase or use a poly/athletic ink Stretchable & flexible — moves with the garment without cracking Creamy & print-ready — smooth lay-down on manual or automatic presses 62 colors, pint to 5 gallon (plus 30 & 55 gallon drums) CPSIA-compliant & phthalate-free — safe for kids' apparel, made in the USA Always run a test print first. Before any production run, print and fully cure a test on your exact garment and check opacity, hand and wash-fastness. It's the best habit in the shop — if you're not sure on settings, call us at 201-487-9600 before you run the job. What it prints on 100% cotton — maximum opacity and bright color 50/50 cotton/poly blends Light-color polyester — low-bleed; for dark or high-bleed poly use a grey blocker underbase or a poly/athletic ink Printing & curing Mesh: 110–160 for maximum opacity on darks; finer (200–355) for detail and halftones Squeegee: 65, 75 or 80 durometer — or a 70/90/70 triple durometer for sharp edges with easy fill Flash: 240–260°F between colors Cure: curing is a time-and-temperature process — bring the full ink film to 300–310°F (150–154°C); confirm with a temp gun or donut probe, not dryer air temp Recommended companion products Nylon Bond 289 Additive — mix into this ink to bond prints to nylon and other slick synthetics (catalyst; stir in a small amount, limited pot life, always test first). Quick Flash Reducer — thins the ink for easier printing and finer detail without killing opacity. Soft Hand Base — add for a softer, lighter hand feel on the garment. Badass Puff Additive — mix in for a raised, high-rise puff effect. Pantone® Custom Color Match — send us your target Pantone® and we custom-mix the color for you (plastisol, solvent, UV & water-base). Cleanup: OPTI Wash 125 (odor-free screen & tool wash) and OPTI Spot 303 (spot cleaning). Custom color matching We are a Pantone® certified company. Match any Pantone® color with our UMX (Ultimate Mixing System) — verified under D50 lighting, standard turnaround 48–72 hours. Free software at umxsystem.com. How close are we to your Pantone? See our Standard Color → Pantone® (PMS) Match Chart — the closest Pantone® reference for every Total Ink Solutions standard color, with RGB and HEX values. For an exact, verified match, our UMX® system mixes to your target. Safety, PPE & storage Wear nitrile gloves and safety glasses; avoid prolonged skin contact with uncured ink. Print with adequate ventilation; curing releases vapors — vent your dryer. Always stir the ink before use — standard practice to re-blend any settling. Storage & shelf life: keep sealed and out of direct sunlight. Shelf life is 1–2 years for standard inks; low-cure and all-polyester inks must be stored at 60–80°F. In high heat expect some expansion in the container — open carefully. Do not freeze. Uncured ink is not hazardous waste but should be handled and disposed of per local regulations. Refer to the Safety Data Sheet before use. Compliance CPSIA compliant — meets 16 CFR Part 1303 (
