International Interprotect is a high performance two pack primer/undercoat. Easy to apply and quick drying, An epoxy polyamide primer that can be recoated with itself for up to 6 months Easy to sand and quick to dry Good abrasion resistance Offers excellent anticorrosive protection Can be used as an antifouling tie-coat over existing epoxy primers Below the Water: First Coat thinned 10-15% with Thinner No.7, then 4-5 coats Use in these areas Suitable for above and below waterline Hull Keel Bilge/Lockers Exterior cabin/trims Interior cabin/trims Propeller Drive Use for substrates Aluminium / Zinc-Galvanised Steel Epoxy Composite / Carbon Fibre GRP / FRP Lead Steel Wood Pack Size 750ml Preparation Steel: Degrease with solvent or Super Cleaner. Grit-blast to Sa 2½ - near white metal surface. If grit-blasting is not possible, grind the metal surface with 24-36 grit abrasive discs to a uniform, clean, bright metal surface with a 50¬75 microns anchor pattern. Use angle grinder on small areas. Aluminium: Degrease with solvent or Super Cleaner. Sand well using 24- 120 grade (aluminium compatible) paper. Coarser grades are recommended to achieve optimum adhesion. Clean thoroughly and allow to dry. Prime using a recommended International primer as soon as possible (within 8 hours) as detailed for specific coating systems. Zinc/Galvanised Steel: Degrease with solvent or Super Cleaner. Sand well using 60-120 grade paper. Clean thoroughly and allow to dry completely. Prime using a recommended International primer as soon as possible (within 8 hours) as detailed for specific coating systems. Stainless Steel: Light grit blast to produce a profile of 50 microns. Clean thoroughly and allow to dry completely. Prime using a recommended International primer as soon as possible (within 8 hours) as detailed for specific coating systems. Lead: Degrease with solvent or Super Cleaner. Sand well using 120 grade paper or power wire brush clean thoroughly and allow to dry. Prime using a recommended International primer as soon as possible (within 8 hours) as detailed for specific coating systems. Bare Wood: Sand smooth with 80-180 and then 280 grade paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent then allow to dry completely before applying products recommended for application direct to wood (see specific coating systems). Hazard Warnings Hazard Pictogram : Signal Word: Warning Hazard Statements: Flammable liquid and vapourCauses skin irritationCauses serious eye damageMay cause an allergic skin reactionHarmful to aquatic life with long lasting effects Precautionary Statement: General: Keep out of reach of children. Prevention: P210 - Keep away from heat / sparks / open flames / hot surfaces - No smokingP260 - Do not breathe mist / vapours / sprayP261 - Avoid breathing dust / fume / gas / mist / vapours / sprayP264 - Wash thoroughly after handlingP272 - Contaminated work clothing should not be allowed out of the workplaceP273 - Avoid release to the environmentP280 - Wear protective gloves / eye protection / face protection Response: P301+310 IF SWALLOWED - Immediately call a POISON CENTER or doctor / physicianP302+352 IF ON SKIN - Wash with soap and waterP303+361+353 IF ON SKIN (or hair) - Remove / Take off immediately all contaminated clothingRinse skin with water / showerP305+351+338 IF IN EYES - Rinse continuously with water for several minutesRemove contact lenses if present and easy to do - continue rinsingP310 - Immediately call a POISON CENTER or doctor / physicianP321 - Specific treatment (see information on this label)P331 - Do NOT induce vomitingP333+313 - If skin irritation or a rash occurs: Get medical advice / attentionP362 - Take off contaminated clothing and wash before reuseP363 - Wash contaminated clothing before reuseP370 - In case of fireP378 - Use alcohol resistant foam, CO2, powder, water spray for extinction. Do not use water jet Storage: P403+233 - Store in a well ventilated place. Keep container tightly closed. Disposal: P501 - Dispose of contents / container in accordance with local / national regulations. Hazardous Ingredients Epoxy Resin, N-Butanol, Xylene, Ethyl Benzene, Solvent Naphtha (petroleum), Light Aromatic, Amorphous Silica Gel, Aluminium Hydroxide. Interprotect Part A White Safety Data Sheet Interprotect Part B White Safety Data Sheet Interprotect Part A Grey Safety Data Sheet Interprotect Part B Grey Safety Data Sheet
Related
Related
Related
Related