Key Features Repeatable Cut Lengths Set the stop once, slide your stock in, and cut matching parts without marking every board. That saves time and cuts down on small measuring mistakes that add up fast. 8 Feet of Trak The Kreg KMS8000 Precision Trak & Stop Kit includes four 2-foot sections, so you can run support and measuring capacity on one side of the saw or split it between both sides. Two Stop Styles A Production Stop handles repetitive work, while the Swing Stop gets out of the way when needed. You get a setup that works for batch cutting and one-off cuts on the same station. Overview The Kreg KMS8000 Precision Trak & Stop Kit is a measuring and stop system built to turn a basic saw station into a more accurate cutting setup. This is a precision trak and stop kit designed for repeatable length cuts on miter saw stations. Model Number KMS8000. If you are tired of marking every board with a tape measure and pencil, this setup gives you a faster way to make parts to the same length again and again. What matters most here is how the system works in real use. You position the stop using the precision lens cursor, push the board against the stop, and cut to that length consistently. That is the real benefit of this kind of miter saw accessory. It speeds up production work, helps keep cabinet parts and trim pieces uniform, and removes a lot of the guesswork that comes from reading and transferring measurements over and over. The aluminum trak is split into four 2-foot sections for a total of 8 feet, which gives you some flexibility when you build out your station. You can place all 8 feet on one side, split it 4 feet and 4 feet, or run 2 feet on one side and 6 feet on the other. For a small shop or a custom saw bench, that matters because you can set the station around the work you do most instead of being locked into one fixed layout. Kreg also built this system around practical shop use. The anodized aluminum trak uses an L-shaped base that makes alignment and mounting easier on a 3/4 inch board. The groove along the top accepts the included self-adhesive measuring tapes, so you get a readable reference built right into the fence line. That keeps the measuring point where you need it instead of reaching for a tape every time. The two included stops give the kit more range than a basic single-stop setup. The Production Stop is meant for repetitive cuts and has dual lens cursors so it can be used on either side of the blade. The Swing Stop is useful when you need precise positioning but do not want the stop staying in the way between cuts. On a busy bench, that kind of small detail makes the workflow smoother. This system is most commonly used with a miter saw, but it can also be useful on a radial arm saw or drill press where controlled positioning matters. It does require a shop-made support wing or fence setup, so it is best for woodworkers, trim carpenters, and serious DIY users who want to build a proper station once and get cleaner, more repeatable results from it after that. Dial In Accurate Repeat Cuts If your work depends on making the same cut more than once, this kit earns its keep quickly. Set your measurement at the cursor, run the stock to the stop, and keep moving. Precision lens cursor helps position the stop quickly and accurately Built to remove repeated tape measure and pencil layout for length cuts Set Up the Station Your Way The four-section trak design gives you flexibility instead of forcing one layout. That makes it easier to build around your saw, available bench space, and the lengths of stock you cut most often. Includes 8 feet of trak in four 2-foot sections Can be used on the right side, left side, or split between both sides of the saw Use the Stop That Fits the Job Not every cut is the same, and Kreg did a good job accounting for that. The Production Stop is built for repeated parts, while the Swing Stop gives you a precise reference that can move out of the way when you need open access. Production Stop features dual lens cursors for use on either side of the blade Swing Stop can be pushed temporarily out of the way or swung up when not needed What's in the Box (4) 2 ft. anodized aluminum trak sections (1) Production Stop (1) Swing Stop (2) Self-adhesive measuring tapes Instructions and mounting hardware Support wings are shop-made and must be built separately. Key Specifications Total Trak Length 8 ft. (2438 mm) Section Length 2 ft. (610 mm) each Section Count 4 Mounting Board Thickness 3/4 in. (19 mm) Fence Height Above Saw Table 2-1/4 in. (57 mm) Measuring Tapes Included 2 Material Anodized aluminum trak Weight 5.0 lbs Compatibility Primary Machine Type Designed primarily for miter saw cutting stations. Alternative Shop Use Can also be used with a radial arm saw or drill press where controlled positioning is useful. Mounting Surface L-shaped base is designed to mount to a 3/4 in. thick board in a shop-made support wing setup. Built For Woodworking Carpentry Trim Work Miter Saw Stations Repeat Cut Production Shop Fixtures Pro Tip Before you stick down the measuring tape, get your support wings and fence perfectly flush with the saw table and verify the blade reference with a test cut. A few minutes there is what makes the cursor read true later. Warranty & Support 3-year warranty. Tool Nut's Take Tool Nut's Take Why the Kreg KMS8000 Precision Trak & Stop Kit Makes Sense This is the kind of shop upgrade that feels simple until you use it, then you wonder why you spent so long measuring every board by hand. Who it's for: Woodworkers, trim carpenters, and serious DIY users building a dedicated miter saw station for repeatable cuts. Why it stands out: You get 8 feet of adjustable anodized aluminum trak, a Production Stop, a Swing Stop, and the cursor system that makes setup quick and dependable. Worth knowing: This is not a freestanding stand. You need to build the support wings, so it is best for users ready to set up a proper bench instead of looking for a plug-and-play saw stand accessory. Common Questions What kind of tool is this? It is a measuring and stop system for creating repeatable cut lengths, most commonly on a miter saw station. How much trak is included? The kit includes 8 feet of trak supplied as four 2-foot sections. Can it be split between both sides of the saw? Yes. The sections can be configured on the right side, left side, or divided between both sides. Does it only work with a miter saw? No. It is most commonly used with a miter saw, but it can also be useful on a radial arm saw or drill press.
