SPECIFICATIONSBrand Name: LAUNCHHign-concerned Chemical: noneOrigin: Mainland ChinaHardware Version: newestSoftware Version: newestItem Type: Code Readers & Scan ToolsCertification: CELanguage: germanLanguage: FRENCHLanguage: RussianLanguage: ItalianLanguage: EnglishLanguage: SpanishSoftware Update: YesCreader 3001 function: Support full OBDII/EOBD functionCreader 3001 feature 1: I/M readinessCreader 3001 feature 2: Freeze dataCreader 3001 feature 3: code reader scannerCreader 3001 feature 4: auto diagnostic toolLAUNCH CR3001 Language: English , French , Russian , Spanish ,German, Italian ,Portugueselaunch cr3001 Update: Lifetime Free UpdateTechincal Support: Free and in time LAUNCH Creader 3001 OBD2 Scanner Engine Fault Code Reader Mode 6 CAN Diagnostic Scan Tool for All OBDII Protocol Cars Since 1996 Lifetime Free Update Notice Many Customers has the doubt for the time 2019 in the back of CR3001 , pls note , it is the Copyright time , not manufactory time !!! If you care about it , pls do not make the order , thank you ! LAUNCH CR3001 Supports Langauges : English, French, German, Spanish, Russian, Italian, Polish LAUNCH Creader 3001 OBD2 scanner is a very Cost-efficient full OBD2 function scanner on the market (the same functions need 40 ). Unlike other car code readers, Launch Creader 3001 is an all in one car code scanning tool. An upgraded version from the more basic code reader with additional functions. It is designed for car owners, DIYers as well as mechanics to determine the cause and solve the problem. Why Choose LAUNCH Creader 3001? 1. LAUNCH Creader 3001 obd2 scanner Supports O2 Sensor test , EVAP system test, On-Board monitor test, While AD310 and AL319 DOES NOT !2. LAUNCH CR3001 Add more car models , including cars, SUVs,minivans,light-duty trucks all over the world. But the year supported may vary on different car makes and models. LAUNCH CR3001 Support Full OBD2 functions, Engine Check including : Reading Codes:Show the detailed description of the Diagnostic Trouble Code (DTCs)Erasing Codes & Reset:Turns off Check Engine Light (MIL), clears codes and resets monitors.Data Stream:Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.I/M Readiness Status:Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.Read Live Data Stream:Show the information of continuous data stream from a vehicle in live graphic (waveform) display.View Freeze Frame Data:Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.O2 Sensor Test:Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.On-Board Monitor Test:Retrieves and displays test results for emission-related powertrain components and systems.Read Vehicle Information:Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.Component Test:Certain vehicle components can be actuated by commands sent from the scanner to test their operability Turn Off ''Check Engine'' Light Parts might cause your check engine light on include:1. Gas Cap 2. Oxygen Sensor 3. Air Fuel Ratio Sensor 4. Mass Air Flow Sensor 5. Ignition Coils 6. Spark Plug Wires 7. Spark Plugs 8. Thermostat 9. EGR Valve 10. Evaporatative Emission Canister Purge Valve(EVAP) 11. Catalytic Converter.If the engine light is not turned off in timeit will Cause Serious environmental pollution , Increased fuel consumption,Increased engine noise.Increased in temperature , ect How to verify whether the vehicle will pass the emission test with this code reader? After entering the I/M Readiness, there will be 10 results on the list. Misfire monitor, fuel system, componentmonitor, catalyst monitor, heated catalyst, EVAP system, secondary air sys, 02 sensor, O2 sensor heater EGRand/or WVT. There will be an OK if each of them works fine. [Not all vehicles have these 10 parts] LAUNCH CR3001 Screen Display Support Car Models for OBDII diagnostic function: (Note: CR3001only Support 12V Gasoline& Diesel, Does not support 24V Truck)American Car :Need Standard OBD2 Protocols from 2000 to nowfor Chrysler , for Ford, for GM, For Jeep ...European Car :Need Standard OBD2 Protocols from 2003 to nowFor Alfa romeo , for SAAB ,for Acura , for Opel , for Audi for Seat , for Peugeot , for RenaultFor Bentley , for Skoda , for Daewoo , for Benz , for Daihatsu , for Land Rover , for BMW , for Vauxhall , for Citroen , for Volvo , for Fiat , for VW , for Ford , for Jaguar...Japanese/Korean Car:Need Standard OBD2 Protocols from 2006 to nowfor KIA, for Isuzu, for Honda , for Mitsubishi, for Hyundai , for Dacia , for Lexus , for Mazda, for Nissan, for Subaru , for Suzuki, for Toyota..Chinese Car:Need Standard OBD2 Protocols from 2009 to now LAUNCH CR3001 Support OBD 2 protocols car : 1.SAE J1850 PWM(41.6Kbaud)2.SAE J1850 VPW(10.4Kbaud)3.ISO9141-2(5 baud init,10.4Kbaud)4.ISO14230-4 KWP(5 baud init,10.4 Kbaud)5.ISO14230-4 KWP(fast init,10.4 Kbaud)6.ISO15765-4 CAN(11bit ID,500 Kbaud)7.ISO15765-4 CAN(29bit ID,500 Kbaud)8.ISO15765-4 CAN(11bit ID,250 Kbaud)9.ISO15765-4 CAN(29bit ID,250 Kbaud) LAUNCH CR3001 is with Lifetime Free Update If the product displays a white screen or cannot support your car, you can solve it by upgradingSupport update system :compatible with Windows XP, Windows 7, Windows 8 & Windows 10 Easy to Carry The OBD2 scanner's mini size fits comfortably in the palm of your hand. so that you can carry it around no matter in garage or on a trip. USER-FRIENDLY Dust Cap Design : protect the connector from dust, water, resistant oil and dirtly , no worries while you donrsquot use it . LAUNCH CR3001 Update Process : Step 1 : Go to LAUNCH Website : https://eninfo.x431.com/ , to download Updatetool Step 2 : Install the updatetool in your company Step 3 : Connect CR3001 with computer , then Click Update button to Update . If you still do not know how to do , pls check the update video in the following How to use CR3001 ? LAUNCH CR3001 Specifications: Screen :1.77 " TFT, 160*128dpiVoltage Range: 9-18VOperating Temperature :0℃ -50 ℃ (32 ℉ -122 ℉ )Environment Temperature -20 ℃ -70 ℃ (-4 ℉ -158 ℉ )Dimension : 118mm*68mm*22.3mm(4.65" *2.68 " *0.88 " )Weight:
Related
Related
Related
Related