Sturdy and versatile LeClerc Hand & Electric Single and Double Ended Bobbin Winders. The Hand Winder is compatible with all Leclerc Bobbins & Leclerc Spools, while the Electric Winder has a single and double ended winder available. The Single works with regular Leclerc 4"/10cm, 6"/15cm bobbins, & Leclerc spools, and the double is compatible with all bobbins, spools, pirns between 2.75" - 8" (25mm - 20cm). The Electric Bobbin Winder is available with or without the Tension Device & Counter. About the tension device: The tension device combines four pegs for tensioning along with metal eyes to guide the yarn. These ride on a wooden block that slides back and fourth on a metal shaft. Feed the yarn through the eyes, wrap it around as many pegs as you need to get the proper tension for your yarn, and wind it on the bobbin. As you wind, slide the tension device back and forth to control the build-up of the yarn on the bobbin. Hand Bobbin Winder - All Leclerc Bobbins & Spools: 6331-1000 A light but strong hand bobbin winder with completely covered gear. Tapered plated shaft for all LeClerc bobbins and Leclerc Spools. Clamps to a table top up to 1½" thick. Turning ratio: 1/7.5 Wood handle. Hand Winder Maintenance The handle is held on by a bolt threaded into the body, with a nut behind it setting the position. Inside the handle, a ring of teeth meshes with the gear on the shaft. Hard to turn? Back the bolt and nut off slightly. Done up too tight, they pinch the handle. Wobbling or unsteady? The bolt has worked its way out. Snug it in, then bring the nut up to hold it. Stiff after long storage? The grease has hardened. Take the nut off, back the bolt out, lift the handle away, and pack the teeth on its inner face with ordinary gear grease. Reassemble by feel. Run the bolt in until it is just too tight to turn, back it off slightly, and do the nut the same way. You want no effort to turn and no side to side play. Electric Single Ended Bobbin Winder - 4" / 6": 6334-1000 With a tapered shaft to be used on regular Leclerc 4" (10 cm) bobbins, 6" (15 cm) bobbins, and Leclerc spools. Foot operated speed control. Electric Double Ended Bobbin Winder 2.75" - 8": 6334-9000 Holds both ends of bobbins, spools or pirns. Designed for bobbins, spools or pirns of any length between (25 mm to 20 cm). Foot operated speed control Electric Double Ended Bobbin Winder w/ Tension Device & Counter : 6334-9001 *COMPLETE PACKAGE* Holds both ends of bobbins, spools or pirns. Designed for bobbins, spools or pirns of any length between 2.75" to 8" (25 mm to 20 cm). Foot operated speed control With the tension device and the counter (Yard or Meter) Electric Double Ended Bobbin Winder w/ Tension Device: 6334-9002 Holds both ends of bobbins, spools or pirns. Designed for bobbins, spools or pirns of any length between 2.75" to 8" (25 mm to 20 cm). Foot operated speed control With the tension device PLEASE NOTE: Our first response to your order would be to have it shipped directly from our warehouse. In the case that our stock levels are too low, your order may need to be either ordered into our warehouse or dropshipped directly to you fromLeClerci’s warehouse in Canada. Please allow at least 4-5 business days for them to process and ship out your order before receiving an e-mail with your tracking number. Should your order be backordered with our vendor, one of our customer service representatives will contact you with delays and shipping information. Please note that LeClerc drop-ships are typically sent via UPS. Please provide a physical address for your order as UPS does not send to PO Boxes. Drop-shipping is not available for international orders at this time so please allow time for your order to reach us before we ship it to you. Please contact us with any questions or concerns regarding your order at (509) 536-7746 or [email protected].
