The Forward 991595 replacement hardware is the direct replacement for the Forward lift it came off of. Cross-referenced as ALS-7239-587, it is the genuine Forward part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Forward replacement hardware from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same. Specifications Part number: ALS-7239-587 Brand: Forward Type: Genuine OEM replacement hardware Hardware is the easiest category to order wrong, because so much of it looks generic — a pin is a pin until it is an eighth of an inch short and the e-clip groove lands inside the bore. Lift makers change hardware dimensions between production runs without renaming the lift, so the part that fits a given model can split by serial range. Order from your lift’s data tag — model and serial — rather than from the model name or from a lookalike photo. If the tag is gone, the old hardware itself is the spec: measure it, or photograph it next to a tape measure and send it to us, and we will match it before it ships. Related parts for this lift The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit. Bearing CR14, RFP14 - Forward - H4P-3001 Spring CR14, RFP14 - Forward - H4P-1015 Roller Pin - Forward - FC5991Y Pin - Forward - H4P-1017FWD 3/8 JIC Swivel Nut 45 Deg #6502-6 - Forward - 992464 Shaft Weldment - Forward - 250405 Check your lift's serial before ordering The most common reason a lift part comes back is not a defect — it is a revision mismatch. Manufacturers change sub-parts between production runs while keeping the same lift model name, so "it fits my lift model" is not always enough. The model plate carries the serial number that pins your lift to a specific run, and that is the number that settles which version of this part belongs on your lift. Can't find the plate? Measure the old part — overall length, bolt-hole spacing, thread size on anything threaded — and photograph it from a couple of angles. Send that with your lift's brand and rough age and we will match it against the parts breakdowns we service from every week. Measure the old part before you order and again against the new part when it arrives: overall length, diameter, groove and cross-hole locations, and thread size on anything threaded. On threaded hardware, run the nut on by hand first — if it fights, check for welding slag or damaged threads and clean them up with a file rather than powering the nut on and wrecking both parts. Close is not correct on load-bearing hardware. A pin that is slightly undersized hammers its bore oval; a bolt of the wrong grade shears under a load the right one shrugs off. If what arrived does not match what came out, install nothing and call — guessing is the one move with no good outcome. Why buy your Forward replacement hardware from Auto Lift Services We install, inspect, and repair Forward lifts every week — the ALS-7239-587 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302. We confirm the right part for your lift's serial and production year before you order. Every part ships as genuine Forward — no aftermarket substitution unless you specifically ask for an aftermarket equivalent. If you also need companion wear items — cables, sheaves, seals, hardware — for the same repair, use our parts lookup and we will build the whole kit for your lift so you order once and finish the job. About this 991595 lock pin Sourcing the correct 991595 lock pin is not the spot a shop wants to gamble. This piece sits inside a load path the lift manufacturer engineered to specific tolerances, and a substitute that looks close but is off by even a small margin can transfer load onto a neighboring component that was not designed for it. We stock this exact part to the OEM specification the original manufacturer publishes, which is why techs who have been through a bad aftermarket cycle keep coming back to us for the same replacement whenever their next need comes up. Technical specification & installation notes Torque and installation notes for this component follow the manufacturer's service manual. Where a torque value is called out, use a calibrated torque wrench and follow the tightening sequence the manual publishes for that fastener location — many lift assemblies require star-pattern or crosswise tightening to distribute load evenly. Skipping that step is one of the most common reasons a correctly-sourced 991595 lock pin still ends up needing to be re-serviced within a year. Our tech line at 800-674-9302 will walk your installer through the procedure if the shop does not have the current service manual on hand. Shipping & ordering Freight covers the continental United States on all standard orders. We ship UPS or FedEx ground for parts under 30 lb; heavier assemblies quote at published carrier rates. International orders on the 991595 lock pin require a freight quote — email dimensions, weight, and destination country to [email protected] and we return a rate within one business day. Alaska, Hawaii, and US territories quote at published rates and typically take five to ten business days depending on carrier and destination. Warranty coverage Consumables and wear parts like this are covered under the manufacturer defect warranty for twelve months. Because the 991595 lock pin is a component that eventually needs replacement in normal operation, warranty coverage specifically addresses failure due to manufacturing defect, not failure due to normal end-of-life wear. Our team can help distinguish between the two on a phone call if there is any question after installation — call 800-674-9302 and describe the failure pattern; we will tell you honestly whether it looks like a warranty case. Cross-reference & fitment Cross-reference on the 991595 lock pin is straightforward: match the OEM part number from the lift's parts breakdown against the number on your original invoice. If the numbers match, the component fits. If your lift's parts breakdown lists a superseded or alternate number, we accept the superseded value on the phone as confirmation of fit. When a manufacturer has issued a running change during production, we track the change in our catalog so ordering by the older number automatically pulls the current-spec replacement. Questions about the 991595 lock pin? Call our parts desk at 800-674-9302 or email [email protected]. We ship nationwide from our Iowa warehouse and answer fitment questions within one business day.
