LoRa-E5 mini is a compacted-sized dev board suitable for rapidly testing and building a small-size LoRa device and application prototyping. LoRa-E5 mini is embedded with and leads out full GPIOs of LoRa-E5 STM32WLE5JC. It has rich interfaces including UART, ADC, SPI, IIC,etc. Supporting LoRaWAN protocol and global frequency, LoRa-E5 mini is able to achieve a transmission range of up to 10 km in open area and ultra-low power consumption. Features Full GPIOs led out from the Lora-E5 STM32WLE5JC Global LoRaWAN® and LoRa frequency plan supported Long-distance transmission range to 10km (ideal value in open area) Mini and compact size, suitable for rapid testing and building small size prototype Convenient RESET and BOOT buttons on board LoRa-E5 mini is a compact development board suitable for the rapid testing and building of small-size prototyping and helps you design your ideal LoRaWAN wireless IoT device with a long-distance transmission range. LoRa-E5 mini is embedded with the LoRa-E5 STM32WLE5JC Module, which delivers the world-first combo of LoRa RF and MCU chip into one single tiny chip and is FCC and CE certified. It is powered by ARM Cortex-M4 core and Semtech SX126X LoRa chip and supports LoRaWAN protocol on the worldwide frequency and (G)FSK, BPSK, (G)MSK, and LoRa modulations. (Learn more about LoRa-E5) LoRa-E5 mini leads out all GPIOs of LoRa-E5, including UART, ADC, SPI, IIC, etc. It contains RESET and BOOT buttons and is user-friendly. Supporting LoRaWAN protocol, LoRa-E5 mini features ultra-long-range transmission and ultra-low power consumption: it is able to achieve a transmission range of up to 10 km, and the sleep current of LoRa-E5 modules on board is as low as 2.1 uA(WOR mode). It is designed with industrial standards with a wide working temperature at -40 ℃ ~ 85℃, high sensitivity between -116.5dBm ~ -136 dBm, and power output up to +20.8 dBm at 3.3V. Since LoRa-E5 is a LoRaWAN chip with an MCU, there are three main ways to utilize the LoRa-E5 mini: Connect LoRa-E5 mini to PC and control by AT commands There is a built-in USB to UART function on board, you could connect the LoRa-E5 mini to your PC with a USB type C cable, and use serial communication software to send AT commands and read data from the board. Connect LoRa-E5 mini to another mainboard via UART and control by AT commands For example, connect LoRa-E5 mini to Seeeduino XIAO and the Expansion Board via UART, and send AT commands and read data from Seeeduino XIAO through Arduino IDE serial monitor. User Application Development by using SDK Develop your own LoRa development board with MCU function by using STM32Cube Programmer, which is the SDK officially provided by STMicroelectronics. To download this SDK resource, please find the resources linked below. With all the outstanding features listed above, the LoRa-E5 mini will be a superior choice for IoT device development, testing, prototyping, and applications in long-distance, ultra-low power consumption IoT scenarios like smart agriculture, smart office, and smart industry. If you are unfamiliar with LoRa and LoRaWAN technology, please check out this blog LoRapedia in detail. Application Note For more detailed information about how to use LoRa-E5, please visit LoRa-E5 (STM32WLE5JC) Module Wiki. 1. Factory AT Firmware LoRa-E5 series has a built-in AT command firmware, which supports LoRaWAN Class A/B/C protocol and a wide frequency plan: EU868/US915/AU915/AS923/KR920/IN865. With this AT command firmware, users can easily and quickly build their prototype or application. The AT command firmware contains a bootloader for DFU and the AT application. The "PB13/SPI_SCK/BOOT" pin is used to control LoRa-E5 to stay in the bootloader or jump to the AT application. When PB13 is HIGH, the module will jump to AT application after reset, with a default baud rate of 9600. When PB13 is LOW (press the "Boot" button on LoRa-E5 Dev Board or LoRa-E5 mini), the module will stay in the bootloader, and keep transmitting "C" character every 1S at baud rate 115200. Attention Factory AT Firmware is programmed with RDP(Read Protection) Level 1, developers need to remove RDP first with STM32Cube Programmer. Note that regression RDP to level 0 will cause a flash memory mass to erase and the Factory AT Firmware can't be restored again. The "PB13/SPI_SCK/BOOT" pin on the LoRa-E5 module is just a normal GPIO, not the "BOOT0" pin of the MCU. This "PB13/SPI_SCK/BOOT" pin is used in the bootloader of the Factory AT firmware, to decide to jump to APP or stay in bootloader(for DFU). The real "BOOT0" pin doesn't pinout to the module, so developers need to be careful when developing low-power applications. 2. Clock Configuration 2.1 HSE 32MHz TCXO TCXO power supply: PB0-VDD_TCXO 2.2 LSE 32.768KHz crystal oscillator 3. RF Switch LoRa-E5 module ONLY transmits through RFO_HP: Receive: PA4=1, PB5=0 Transmit(high output power, SMPS mode): PA4=0, PB5=1 Specifications Parameters Specifications size 50 x 23mm voltage - supply 3.7V - 5V power - output up to +20.8 dBm at 3.3V working frequency 868/915MHz protocol LoRaWAN sensitivity -116.5 dBm ~ -136 dBm interfaces USB Type C / 2P-2.54mm Hole / 1*12P-2.54mm Header*2 / SMA-K / IPEX modulation LoRa, (G)FSK, (G)MSK, BPSK working temperature -40℃ ~ 85℃ current LoRa-E5 module sleep current as low as 2.1uA (WOR mode) Part List: LoRa-E5 mini x1 Antenna(EU868/US915) x1 USB TypeC (20cm) x1 Sticker x1 1X12pin male pin headers x2 Documentation LoRa-E5 mini Datasheet: LoRa-E5 mini v1.0.brd LoRa-E5 mini v1.0.pdf LoRa-E5 mini v1.0.sch LoRa-E5 Datasheet: LoRa-E5 datasheet and specifications LoRa-E5 AT Command Specification STM32WLE5JC Datasheet LoRa-E5 Certifications: LoRa-E5-HF Certification CE-VOC-RED LoRa-E5-HF FCC Certification -DSS LoRa-E5-HF FCC Certification -DTS Relevant SDK: STM32Cube MCU Package for STM32WL series
Related
Related
Related
Related