Lumishore Delrin Sleeve Kit

SailRACE Verified independent store

→

The Lumi-Cam (TIX402) brings all the amazing detail of magnificent sea life and beautiful underwater terrain to life in vivid high-definition color. The world’s smallest Full HD Me ga Pixel (1080p) underwater camera is compact and 'flush-fit' in design, allowing it to be mounted nearly anywhere on the hull. It’s integrated internal module makes for easy installation. Features Full HD 1080p 67° Viewing angle 3 Year Warranty Dynamic Noise Reduction Composite Output (BNC) HD-SDI Output (BNC) Low Light Mode Wide Dynamic Range Specifications Specification Value Resolution Full HD (1080p) Lens 3.6mm Fixed Focus Viewing Angle 67° Minimum Illumination 0.01 LUX Camera Output HD-SDI or Composite (NTSC/PAL) Supply Voltage 12 V DC Max Current Draw 0.25A Housing Type Marine Grade Aluminum Bronze Downloads FAQs What warranty period is stated in the provided documents?The datasheet states “2 years”, while the installation guide states a warranty “period of three years” from original purchase. How tight should the locking nut be during installation?Tighten the locking nut hand tight. Don’t fully tighten at first (to avoid squeezing out sealant), and avoid excessive force after curing. What hole size is specified when NOT using isolation sleeves?The guide specifies a 2-1/4 in (57 mm) entry hole for installation (without noting sleeve changes). Can I install or remove the thru-hull fitting while the boat is in the water?No. The installation guide warns not to install or remove the thru-hull fitting or insert module with the vessel in the water. How often does Lumishore recommend inspecting the camera module and cable attachments?The maintenance section recommends inspecting the camera module and cable attachments every month. Should the electrical/video connections be enclosed for water protection?Yes. The guide states the connections should be installed inside a waterproof junction box to protect them from water contact. How far below the water surface should the camera be installed?Lumishore recommends installing the camera about 6–10 inches (150–250 mm) below the water surface (not critical). Do I need to seal the inside of the drilled hull hole?Yes. The exposed inner hull surface must be properly sealed to prevent water intrusion into the hull before securing the thru-hull. Any cleaning/solvent warnings before applying sealant?Yes. Remove dirt/grease and existing antifoul, and do not use an alcohol-based solvent because it may adversely affect the sealant. Where should the bonding connection be made?Bond to the bolt on the locking ring as described in the guide. Where do I find the correct hole size when using isolation sleeves?Refer to the manual/sleeve instructions provided with the sleeves to confirm the correct hole size before drilling. How much clearance is needed inside the hull to remove the camera insert module?Allow more than 7 inches of clearance inside the hull so the Camera Insert Module can be removed. How do I align the picture when inserting the camera module?Align the image by positioning the “TDC” marking on the back of the camera module at the top centre when inserted. Who do I contact for help with installation, servicing or advice?Contact the SailRACE team — as certified marine experts we're happy to help with product selection, installation and after-sales servicing, before and after your purchase. {"@context": "https://schema.org", "@type": "FAQPage", "mainEntity": [{"@type": "Question", "name": "What warranty period is stated in the provided documents?", "acceptedAnswer": {"@type": "Answer", "text": "The datasheet states “2 years”, while the installation guide states a warranty “period of three years” from original purchase."}}, {"@type": "Question", "name": "How tight should the locking nut be during installation?", "acceptedAnswer": {"@type": "Answer", "text": "Tighten the locking nut hand tight. Don’t fully tighten at first (to avoid squeezing out sealant), and avoid excessive force after curing."}}, {"@type": "Question", "name": "What hole size is specified when NOT using isolation sleeves?", "acceptedAnswer": {"@type": "Answer", "text": "The guide specifies a 2-1/4 in (57 mm) entry hole for installation (without noting sleeve changes)."}}, {"@type": "Question", "name": "Can I install or remove the thru-hull fitting while the boat is in the water?", "acceptedAnswer": {"@type": "Answer", "text": "No. The installation guide warns not to install or remove the thru-hull fitting or insert module with the vessel in the water."}}, {"@type": "Question", "name": "How often does Lumishore recommend inspecting the camera module and cable attachments?", "acceptedAnswer": {"@type": "Answer", "text": "The maintenance section recommends inspecting the camera module and cable attachments every month."}}, {"@type": "Question", "name": "Should the electrical/video connections be enclosed for water protection?", "acceptedAnswer": {"@type": "Answer", "text": "Yes. The guide states the connections should be installed inside a waterproof junction box to protect them from water contact."}}, {"@type": "Question", "name": "How far below the water surface should the camera be installed?", "acceptedAnswer": {"@type": "Answer", "text": "Lumishore recommends installing the camera about 6–10 inches (150–250 mm) below the water surface (not critical)."}}, {"@type": "Question", "name": "Do I need to seal the inside of the drilled hull hole?", "acceptedAnswer": {"@type": "Answer", "text": "Yes. The exposed inner hull surface must be properly sealed to prevent water intrusion into the hull before securing the thru-hull."}}, {"@type": "Question", "name": "Any cleaning/solvent warnings before applying sealant?", "acceptedAnswer": {"@type": "Answer", "text": "Yes. Remove dirt/grease and existing antifoul, and do not use an alcohol-based solvent because it may adversely affect the sealant."}}, {"@type": "Question", "name": "Where should the bonding connection be made?", "acceptedAnswer": {"@type": "Answer", "text": "Bond to the bolt on the locking ring as described in the guide."}}, {"@type": "Question", "name": "Where do I find the correct hole size when using isolation sleeves?", "acceptedAnswer": {"@type": "Answer", "text": "Refer to the manual/sleeve instructions provided with the sleeves to confirm the correct hole size before drilling."}}, {"@type": "Question", "name": "How much clearance is needed inside the hull to remove the camera insert module?", "acceptedAnswer": {"@type": "Answer", "text": "Allow more than 7 inches of clearance inside the hull so the Camera Insert Module can be removed."}}, {"@type": "Question", "name": "How do I align the picture when inserting the camera module?", "acceptedAnswer": {"@type": "Answer", "text": "Align the image by positioning the “TDC” marking on the back of the camera module at the top centre when inserted."}}, {"@type": "Question", "name": "Who do I contact for help with installation, servicing or advice?", "acceptedAnswer": {"@type": "Answer", "text": "Contact the SailRACE team — as certified marine experts we're happy to help with product selection, installation and after-sales servicing, before and after your purchase."}}]} Show more