** Discontinued - New Version Here ** Matek's M10-5883 GNSS and Compass module support GPS, GALILEO, BEIDOU, and GLONASS. With an integrated QMC5883L magnetic compass, improved RF sensitivity and filters, this is a module that maximizes positional availability in difficult situations with improved dynamic position accuracy. Specifications: GNSS u-blox MAX-M10S (GPS, GLONASS, Galileo and BeiDou) Magnetic Compass QMC5883L Patch antenna 18*18*4mm Input voltage range: 4~9V (5V pad/pin) Power consumption: 13mA UART baudrate: 9600 default Operating Temperatures: -20~80 °C UART(TX, RX) interface for GNSS MAX-M10S I2C(DA, CL) interface for Compass QMC5883L JST-GH-6P connector (SM06B-GHS-TB) GNSS PPS LED, Green. (Solid ON after powering on M10-5883, blinking(1Hz) when GNSS get 3D fix) 23mm*23mm*10mm 9g Wiring and Settings: M10-5883 5V to Flight controller 4~9V M10-5883 RX to Flight controller UART_TX M10-5883TX to Flight controller UART_RX M10-5883 CL to Flight controller I2C_SCL M10-5883 DA to Flight controller I2C_SDA M10-5883 G to Flight controller GND Tips: Compass Alignment(Arrow forward and flat mounting): Tilting the magnetometer is strongly discouraged! INAV/BetaFLight: CW 270° Flip when flight controller arrow is facing forward also. Ardupilot/Mission Planner: Rotation None. Protocol: Ublox 5Hz or NMEA 1Hz ——————– INAV 5.0.0, Betaflight 4.3.0, ArduPilot 4.1 or newer is required. The default configuration on MAX-M10S with ublox FW 5.1 is concurrent reception of GPS, Galileo, and BeiDou B1I with QZSS and SBAS enabled. GLONASS is disabled by default. Beidou B1I (1561.098 MHz) and GLONASS can’t be enabled at the same time. Beidou B1C (1575.42 MHz) and GLONASS can be enabled at the same time. Flight controller firmware(INAV, Betaflight, ArduPilot) don’t support enable Beidou B1C for now. so MAX-M10S can’t receive GLONASS when it works with flight controller (fw INAV, Betaflight, ArduPilot) . with GPS, Galileo, and BeiDou B1I with QZSS and SBAS enabled, MAX-M10s can receive more than 30 Sats with HDOP down to 0.55. Start with u-blox GNSS FW3.01, timepulse is aligned with UTC time and that time is set valid only after leap second is downloaded. That could take up to 12.5 min. Probably PPS LED will not blink immediately after GPS has 3D fixed. The M10-5883 provides the ability to reset the receiver. Bridging “RST” pad to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option. ——————– Make sure to have compass/magnetometer 10cm away from power lines/ESC/motors/iron-based material The scratches on ceramic antenna are the result of tuning the antenna. HD cameras (Gopro, Split, Tarsier, etc) could interfere GPS signal, try turning off HD camera before GPS 3D fix There are reports that Frsky X8R could interfere M9N GPS. If you are using X8R and GPS can’t get 3D locked. power off X8R then test. Includes:1x Matek M10-5883 GNSS and Compass Module1x JST-GH-6P to JST-GH-6P 20cm Silicon Wire
