Matek M10Q-5883 GPS Compass Module for Fixed Wing FPV Matek M10Q-5883 GPS Compass Module for Fixed Wing FPV combines a u-blox M10-series GNSS receiver, QMC5883L compass, and compact patch antenna in a lightweight module for fixed-wing FPV and autopilot navigation builds. This product page is optimized from Shopify product data and Matek's official M10Q-5883 reference. The Matek reference page marks this model as EOL/discontinued and includes a counterfeit warning, so builders should verify wiring, firmware setup, and module sourcing before installation. Product Images Matek M10Q-5883 GPS compass module product image Matek M10Q-5883 GPS compass module product image Matek M10Q-5883 GPS compass module product image Key Features u-blox M10-series GNSS module: designed for GPS positioning in fixed-wing FPV, ArduPilot, INAV, and compact autonomous aircraft builds. Multi-constellation reception: supports concurrent GPS, GLONASS, Galileo, and BeiDou reception for more flexible satellite coverage. Integrated QMC5883L compass: provides an external I2C compass option when the flight controller layout benefits from a separated compass module. 15 x 15 x 4 mm patch antenna: compact high-gain antenna format for lightweight aircraft and clean top-plate mounting. JST-GH-6P wiring: uses a 1.27 mm pitch JST-GH-6P connector and includes a 20 cm JST-GH cable for flight-controller installation. Configuration and Specifications Shopify product Matek M10Q-5883 GPS Compass Module for Fixed Wing FPV SKU TB-M10Q5883 GNSS module u-blox M10-series GNSS module. Supported constellations GPS, GLONASS, Galileo, and BeiDou concurrent reception. Compass QMC5883L magnetic compass over I2C. GNSS interface UART TX/RX. Default baudrate is 9600 according to the Matek reference page. Compass interface I2C DA/CL lines for QMC5883L compass data. Input voltage 4-9 V on the 5V pad or pin. Power consumption About 13 mA according to the Matek reference page. Antenna 15 x 15 x 4 mm patch antenna. Protocol reference UBX 5 Hz for GPS + Galileo + BeiDou B1C + GLONASS, or NMEA 1 Hz. LED behavior Green PPS LED stays on after power-up and blinks at 1 Hz after 3D fix. Connector JST-GH-6P, SM06B-GHS-TB, 1.27 mm pitch. Dimensions 20 x 20 x 12.4 mm. Weight 8 g. Official reference Matek M10Q-5883 Official Reference / Matek GNSS Category Wiring Notes Power: connect the module 5V input to a compatible 4-9 V flight-controller supply and connect GND to GND. GNSS UART: connect module TX to the flight controller UART RX, and module RX to the flight controller UART TX. Compass I2C: connect DA to SDA and CL to SCL on the flight controller I2C bus. Setup: configure the flight-controller GPS and compass settings to match your firmware, port, and aircraft requirements before flight. Packing List 1 x Matek M10Q-5883 GPS compass module 1 x JST-GH-6P to JST-GH-6P 20 cm silicone wire Project Uses Fixed-wing FPV aircraft: compact GPS and compass positioning module for builds that need clean GNSS placement away from electrical noise. Autopilot navigation: useful for flight controllers that accept GNSS over UART and external compass data over I2C. Small UAV layouts: 20 x 20 mm footprint and 8 g weight make it easier to place on constrained frames. Replacement or spare module: suitable when a build needs a UART/I2C GPS compass module rather than a CAN GNSS unit. FAQ Q: Is this a CAN GPS module?A: No. This listing is for the M10Q-5883 UART/I2C GNSS compass module. It is not a CAN GNSS unit. Q: Which compass chip does it use?A: The Matek reference page lists the compass as QMC5883L, connected through I2C. Q: Which satellite systems are supported?A: The module supports concurrent GPS, GLONASS, Galileo, and BeiDou reception. Q: Why does the official Matek page mention EOL?A: Matek marks the M10Q-5883 official reference page as EOL/discontinued. This Shopify listing's availability is controlled by our current store inventory and product status. Q: Were price, inventory, SKU, status, handle, or Shopify media changed?A: No. This optimization updates only the product description and SEO meta description.
