Black Type III Hard Anodized Malkoff MD2 Flashlight with Malkoff M61 SHO, M61, M61N, or M61W. The High/Low Switch is installed and ready to go. The High/Low is controlled by head rotation. The On/Off switch is a forward clicky with momentary function. Outputs and Draws of Drop-ins Drop-in (Tint) 3.8 Volts 6 Volts 7.2 Volts 9 Volts M61 SHO Cool 5700K Amp Draw 650 lumens 11K Lux (candela) 2.2 A 750 lumens 11K Lux (candela) 1.4 A 750 lumens 11K Lux (candela) 1.1 A 750 lumens 11K Lux (candela) 0.9 A M61 Cool 5700K Amp Draw 450 lumens 6.5K Lux (candela) 1.0 A 450 lumens 6.5K Lux (candela) 0.8 A 450 lumens 6.5K Lux (candela) 0.65 A 450 lumens 6.5K Lux (candela) 0.5 A M61N Neutral 4000K Amp Draw 400 lumens 5.0K Lux (candela) 1.0 A 400 lumens 5.0K Lux (candela) 0.8 A 400 lumens 5.0K Lux (candela) 0.65 A 400 lumens 5.0K Lux (candela) 0.5 A M61W Warm 3000K Amp Draw 400 lumens 5.0K Lux (candela) 1.0 A 400 lumens 5.0K Lux (candela) 0.8 A 400 lumens 5.0K Lux (candela) 0.65 A 400 lumens 5.0K Lux (candela) 0.5 A This Flashlight was designed for rugged service from the ground up. It is fully potted to stand up to rough service and recoil. This Item is Covered by Our Lifetime Warranty. It was primarily designed for use with a single protected 18650 rechargeable cell. It will also work with two CR123 primary cells, but you may need to stretch the spring (in the head) to accommodate the shorter length (of the cells). The runtime is dependent on the capacity of the battery(s) used. An approximate runtime can be figured using the following equation. The capacity of the battery(s) ÷ the draw = Runtime. Then subtract 15 to 20% to compensate for overall inefficiency in the system. Example Runtime calculations: M61 SHO using one 3500mah 18650 battery: 3.5 A ÷ 2.2 A = 1.6 hrs - 0.32 = 1.28 hrs. So expect approx. 1.25+ hrs of full output runtime. M61 SHO using two 1500mah primary CR123 batteries: 1.5 A ÷ 1.4A = 1.07 hrs - 0.21 hrs = 0.86 hrs. So expect approx. 30-45 minutes of full output runtime. I'm being conservative here because of the high current draw on primary cells. Flashlight Extras MDX Titanium Pocket Clip: The pocket clip will be installed if purchased on this page. Designed to fit between the Body and Tailcap of the Malkoff MDX Series Bodies. Material: Aerospace Grade ASTM Certified Domestic 6Al/4V titanium (50% more expensive than consumer grade titanium) insures maximum quality and consistency. Sold HERE. MDX/MDM4 Tempered Glass Lens Kit (Ultra Clear): The tempered glass kit will be installed if purchased on this page. This is a 26.4 x 1.6 mm Tempered and AR Coated (UCL) Glass Lens for the MDX Head. Visible Light Transmissibility is 98%. This lens is chemically strengthened, aka chemically tempered, as opposed to heat tempered. High temperature resistance compared to standard acrylic lenses. It is more scratch resistant that float glass. Sold HERE. Made in the USA. Some parts not domestically sourced. WARNING: This light is capable of causing eye damage at close range. Please use the light responsibly!!! Battery Warnings For Rechargeable Li-ion Batteries: - Do Not over-discharge/overcharge - Please recharge drained batteries ASAP - Do Not short circuit - Do Not dispose of in fire - Do Not expose to extreme heat or water - Please be familiar with the handling of rechargeable Lithium-ion batteries prior to their purchase Battery Warnings: Use Only Quality Batteries from Trusted Sources. Lithium Primary and Li-ion Rechargeable Batteries are Inherently Volatile and Dangerous to Store and Use. All Lithium Batteries Introduce the Risk of Fire, Burns, and Explosions. You Assume the Responsibility of Educating Yourself About Their Use and Storage Before Purchase! If You are Uncomfortable With This, Do Not Purchase this Light!
