Microprocessor Flame photometer Microprocessor Flame photometer Salient Features: Microprocessor Based with Printer Interface Auto Gas Cutoff facility Auto Flame Failure Detection Five Measurements in Single Aspiration of the sample Calibration Curve Programmability Using Maximum of 5 Standard Data Processing Through Curve Fitting Techniques- Least Squares, Quadratic Multiple Calibration Curves Saving Facility Printer Attachment Facility Measurement can be done in ppm as well as in meq Setup Storage Facility (up to 10 setup files) Sample Data Storage Facility Direct Results in ppm and meq. Useful for both Medical & Soil Testing Applications Microprocessor Flame Photometers 1600-G comes with Flame Failure detection and Auto Gas Cutoff Facility. In case of power failure, the gas cuts off automatically. In case the flame goes off accidently during work, the flame failure alarm sounds after a few seconds. Microprocessor Flame Photometer 1600-G are used for the determination of Sodium, Potassium, Calcium, Lithium & Barium. They use the latest microcontroller technology and advanced engineering techniques so as to give enhanced accuracy and reproducibility. They have soft touch membrane keys for ease of operation. The solution is aspirated through an atomizer. Air, sample and the fuel are mixed in the mixing chamber which is then sprayed as a very fine mist into the flame. Radiations from the flame passes through specific narrow band interference filter and pass to the photo-detector. The final results are displayed on the 128 x 64 alphanumeric LCD. The standard model comes with 2 filters (Na, K). Additional filters Ca & Li are optional at extra cost. A photoelectric flame photometer is a device used in inorganic chemical analysis to determine the concentration of certain metal ions. MODEL 2600-G : sodium, Na,Potassium K 1600-G : Sodium, potassium, calcium, lithium RANGE General Serum Urine ppm meq/l meq/l meq/l Na: 0 – 100 Upto 250 meq/l, Na: 0 – 200 Na: 0 – 250 ppm 1:100 dil. 1:100 dil 1:100 dil K: 0 – 100 ppm Upto 250 meq/l, K:0–100 K:0–100 1:100 dil 1:100 dil 1:100 dil RANGE Ca: 0 – 100 Upto 250 meq/l, – Ca: 0 – 10 1:100 dil Li: 0 – 2 1:2 dil ppm Upto 250 meq/l, 1:5 dil – 1:100 dil Li: 0 – 100 ppm – Ba: 0 – 100 ppm Sensitivity General: Na: 0.5 ppm, K: 0.5 ppm, Ca: 15 ppm, Li: 0.5 ppm, Ba: 30 ppm Filters Na & K supplied (Ca, Li and Ba are optional at extra cost) {Ba can be factory fitted only} Resolution 0.1 ppm/0.1 meq Reproducibility < 1% coefficient of variation for 20 consecutive samples using 10 ppm Na set as maximum standard Linearity < 2% error when 3 ppm Na/K and 5 ppm Li are set as maximum standard Curve Fit < 2% of FS Accuracy Display 128x64 Alphanumeric LCD with backlit Average Time In-built in software Flame System LPG and Dry Oil Free Sir Detector Silicon Photodiode Calibration Up to 5 Point Calibration with Curve Fitting Software Gas Control Adjustable with knobs Flame Failure Auto Detection Gas Cutoff Automatic Ignition System Auto Ignition Automiser Axial flow type Printer Provision for attachment of dot matrix printer or HP LaserJet/ inkjet (non- windows) printers with USB interface Power 230 V ± 10% AC, 50 Hz Dimensions 285 x 255 x 210 mm (L x B x H) (Approx.) Weight 7.5 Kg (Approx.) COMPRESSOR UNIT Air Supply By oil free mini compressor unit with pressure regulator Combustion Gas LPG controlled by precision regulator Power 230 V ± 10% AC, 50 Hz Dimensions 290 x 255 x 210 mm (L x B x H) (Approx.) Weight 8 Kg (Approx.) ACCESSORIES Power Cord 1 Unit AIR PIPE 1 Unit (Air Tubing with end clamps) GAS PIPE 1 Unit WASTE WATER PIPE 1 Unit BEAKER BOX 1 Unit (Contains 5 Beakers) CHIMNEY 1 Unit INSTRUCTION 1 Unit MANUAL CAPILLARY PIPES 3 Unit Note: Specifications are subject to change due to continuous improvements.
