ODROID-M2 w/Case, 64GB eMMC Included
We recommend using ODROID's 12V/2A Power Supply for the M2 as there is currently some discussion about issues with other Power Supplies like Meanwell. Introducing the ODROID-M2: A powerful leap forward from the M1 series. Over the past two years, we've seen the success of the ODROID-M1 and M1S. These models provided solid performance and versatile I/O configurations that met the needs of most users. However, some customers have expressed a desire for even higher-end models with greater processing power and ODROID listened to them. We're excited to introduce the new ODROID-M2 SBC. Designed for industrial embedded systems that require enhanced computing power, the ODROID-M2 is built to deliver superior performance. Here’s how the ODROID-M2, powered by the RK3588S2 SoC, stands out compared to the original ODROID-M1: Multiprocessing power: Up to 3x faster. Memory bandwidth: LPDDR5 64-bit RAM with more than double the speed. Graphics performance: A GPU that’s over 5x faster. Neural processing: An NPU that’s over 3x faster. Storage speed: On-board 64GB eMMC storage with twice the speed, thanks to a HS400 interface. The RK3588S2 SoC combines multiple high-performance CPU/GPU cores and large cache memory blocks, all within Samsung Foundry’s efficient 8N process. This results in powerful performance with relatively low power consumption. Thanks to the high-speed 64-bit LPDDR5 memory and high-performance GPU, it shows very usable graphics performance in a 4K dual-head display configuration. We connected two 4K monitors using the M2 board’s HDMI port and the Alt-mode USB Type-C port. This demo shows 4K 3D rendering using HW GPU acceleration on the first monitor, and 4K video playback using HW VPU acceleration on the second monitor. Since hardware accelerators are used to run high-end graphics applications, the cooling fan rarely rotates because it does not generate a lot of heat. 4K Dual-head display demo video For detailed internal configuration, please refer to the block diagram shown below. On-board eMMC storage For the first time in the ODROID board series, an eMMC chip is soldered to the PCB by default instead of using a removable eMMC module. We think 64GB capacity is sufficient for building most embedded systems solutions of this category The sequential access speed of the on-board eMMC is approximately 260MB/s, which is about 3 to 5 times faster than typical microSD cards. Note that the ODROID-M1 series supports the eMMC interface of the HS200 specification, but the ODROID-M2 supports the much faster HS400 specification. Benchmark ODROID-M1 ODROID-M2 iozone 1M random read 144.29 MB/s 273.25 MB/s iozone 1M random write 129.45 MB/s 254.15 MB/s iozone 4K random read 27.52 MB/s 27.86 MB/s iozone 4K random write 41.85 MB/s 52.9 MB/s On-board M.2 NVMe slot In case the 64GB storage space of the soldered eMMC memory is insufficient, consider using an industry standard M.2 2280 form factor NVMe SSD. An on-board M.2 NVMe slot is provided to access large amounts of data storage. Unlike the original M1 model’s PCIe 3.0 x 2 lanes configuration, M2 has PCIe 2.1 x 1 lane. The NVMe transfer speed of the M2 has been reduced to about 1/4. However, we still believe that ~400 MiB/s of storage access speed is sufficient for building various high-end embedded systems. Note that M.2 SATA SSD storage devices cannot be used. The M.2 slot supports only the PCIe SSD (M-Key). Real Time Clock The ODROID-M2 has a hardware Real-Time Clock (RTC) and calendar function by embedding the low-power optimized PCF8563 chip. By installing just one CR2032 RTC backup battery, the clock and calendar will continue to operate for nearly 10 years without a main power supply. The battery is not supplied and must be purchased separately. Heatsink cooling fan A high-performance octa-core single-board computer requires power consumption close to 8 watts when the CPU and GPU are continuously subjected to high-computing loads. At this time, considerable heat is generated and a cooling fan is inevitably needed to avoid thermal throttling of the SoC. Accordingly, the cooling fan is included in the kit. The speed of the cooling fan can be controlled using PWM. Free case Using 3D modeling from the early PCB design stage, we were able to complete the case development precisely and rapidly. The case is also included in the kit. SBC 3D model and case Power consumption To create the graph below, we turned on the M2 and recorded the power consumption until the Ubuntu Desktop OS boots and enters Idle mode. We used the SmartPower3 device to examine power characteristics. With Ethernet and HDMI monitor connected, the peak power consumption is close to 8 Watts during booting and very heavy computing, but drops to 2 Watts in desktop GUI idle state. If you remove the HDMI monitor for a headless system, power consumption in idle mode drops to near 1.3 Watt. Additionally, please note that when the Ethernet cable is unplugged, the power drops to 0.9 Watt. Thermal characteristics Thermal throttling does not occur even when performing a CPU stress test while mounted in a case. Because system power consumption is low, less heat is generated. Cooling is sufficient with just the stock heatsink fan. As shown in the graph below, when a stress test was performed on ODROID-M2 with a stock heatsink under room temperature conditions of 35°C, the CPU temperature was about 75°C and maintained the maximum clock frequency. If the room temperature is 25°C and there is no case, the CPU temperature will be around 60°C. Board details A Rockchip RK3588S2 CPU K 1 x MIPI DSI 4 Lanes B 2 x LPDDR5 chips L 1 x M.2 LED Indicator C 1 x 64GB eMMC on-board M 1 x Micro-SD Slot D 1 x Ethernet Transformer P 1 x Power Button E 1 x RJ45 Ethernet Port (10/100/1000) O 1 x Reset Button F 1 x USB 3.0 Type C with Alt-mod DP P 40 x GPIO Pins G 1 x USB 2.0 host Q 14 x GPIO Pins H 1 x HDMI R 1 x RTC backup battery holder I 1 x USB 3.0 host S 1 x UART for System Console J 1x DC Power Jack T 1 x M.2. M-KEY PCIe2.1 1 Lane U 1x Slide Switch (Boot mode select) Specifications Form Factor Board Dimensions: 90mm x 90mm x 21mmWeight: 78g including heatsink, 58g without heatsink Processor Rockchip RK3588S2 ProcessorQuad-Core Cortex-A76 (2.3GHz +/- 0.1Ghz)Quad-Core Cortex-A55 (1.8GHz)ARMv8-A architecture with Neon and Crypto extensionsMali-G610 GPU MP4 (1Ghz)64KB L1 instruction cache, 64KB L1 data cache, 512KB L2 cache, shared by Cortex-A76 processor32KB L1 instruction cache, 32KB L1 data cache, 128KB L2 cache, shared by Cortex-A55 processorL3 data cache: 3MB, shared by 8 processors NPU 6 TOPS@INT8, Integrated AI accelerator RKNN NPU Memory LPDDR5 8 or 16GiB with 64-bit bus width Storage 1 x 64GB eMMC embedded (soldered to the PCB)1 x Micro SD slot (UHS-I SDR104)* Boot priority between eMMC and microSD can be selected with the slide switch1 x NVME M.2 SSD (PCIe 2.1 x 1 lane) Networking 1 x GbE port (RJ45, supports 10/100/1000 Mbps)– LED indicators* Green LED: Flashing by data traffics at 100Mbps connection* Amber LED: Flashing by data traffics at 1000Mbps connection Video output 1 x HDMI 2.0 (up to 4K@60Hz with HDR, EDID)1 x MIPI DSI Interface (30pin connector which is different from 31pin of the ODROID-M1)1 x DP (via USB Type-C port) External I/O 1 x USB 2.0 host port1 x USB 3.0 host port1 x USB 3.0 Type-C (Data communication and DP Alt-Mode, Not a power source/sink)1 x Debug serial console (UART)1 x 40 pin GPIO and 1 x 14 pin GPIO Real Time Clock * On-board very low power PCF8536 RTC chip* CR2032 RTC backup battery holder to keep time and date for near 10 years without main power input Other features * Power button* Reset button* System LED Indicators:– Red (POWER) – Solid light when DC power is connected– Blue (ALIVE) – Flashing like heartbeat while Kernel is running. Solid On in the u-boot stage. Power 1 x DC jack: outer (negative) diameter 5.5mm inner (positive) diameter 2.1mmDC input voltage range: 7.5V ~ 15.5V (12V/2A power adapter is recommended)– IDLE : ≃ 1W without any kind of peripherals– CPU Stress : ≃ 7.5W (Performance governor) without any kind of peripherals– Power Off : ≃ 0W Note: The maximum clock speed of the Cortex A76 big cores is between 2.2GHz and 2.4GHz. (2.3GHz +/- 0.1GHz) In the semiconductor factory’s test process, the power, voltage and thermal characteristics of each individual CPU are measured and the appropriate maximum clock value is stored in OTP memory as a PVTM. This value cannot be changed by the user. When we tested over 100 samples of M2 boards, most were in the 2.2 ~ 2.3 GHz range, while only a few exceeded 2.3 GHz. GPIO Header There are 40-pin and 14-pin header pin connectors for general purpose input and output functions. Digital IOs, UARTs, I2Cs, PWMs, ADCs, SPI, Analog audio output, Power-on and Reset signals are available. IMPORTANT: Please note that the ODROID-M2 14-pin header pin-map is quite different from the ODROID-M1S due to the missing USB 2.0 signals and different power rails. MIPI-DSI The four-lane MIPI-DSI port can be directly connected to an LCD panel. The ODROID-Vu8S kit with an 8 inch, 800×1280 wide viewing angle LCD and capacitive multi-touch screen is an available option. If you assemble the ODROID-M2 single board computer on the rear side of the Vu8S kit, you can easily implement a Human-Machine-Interface (HMI) device with Android as well as Linux. Software support Android 13 Based on AOSP Tiramisu Customized raw GPIO access framework : Android Things with various examples (https://wiki.odroid.com/common/android_things) I2C (Color sensor, Temperature, Humidity, OLED, RTC) SPI ( CAN receiver, LED strip lights, IO expander) UART ( Loopback test, Barcode scanner, Thermal printer) GPIO toggling Rotary encoder with GPIO IRQ PWM outputs Ubuntu 20.04 LTS (24.04 with newer kernel version will be available a few months later) Kernel 5.10 Wayland based GNOME desktop ARM Mali Bifrost GPU OpenGL-ES / EGL driver MIPI DSI driver GPIO drivers and WiringPi library NPU driver and Neural Network APIs VPU driver with MPP/Gstreamer APIs WIKI : https://wiki.odroid.com/odroid-m2/odroid-m2 NOTES According to the ODROID WiKi SiliconPower NVMe's are not compatible with the ODROID-M2