This universal kWh meter can be used on nearly any electrical system in common use and can also count pulses from up to 3 pulse-output devices, as well as control up to 2 external relays. ~section 2~ Description: Universal, Pulse Counting, Relay Controlling, Smart Meter Features: Pulse Counting and Relay Controls Voltage: 120 volts, 120/240 volts, 120/208 volts, 230 volts, 277 volts, 480 volts Amperage: Up to 5000 amps Type: External CT, 50 or 60 Hz System: Single-Phase, 3-Ph. 3-Wire, or 3-Ph. 4-wire Data: Smart Meter v.4 RS-485 Communications Model: EKM-Omnimeter Pulse v.4 The Omnimeter Pulse v.4 is our most advanced universal smart meter to date, with the ability to count pulses from up to 3x pulse-output devices, and control 2x external relays. This is truly the one meter to meet all of your metering needs! This is a revenue-grade universal kWh meter. It can meter systems ranging from single-phase 120V 2-wire or single phase 120/240V 3-wire, 120V to 480 volts, or 3-phase 3-wire 120 to 415 volts or 3-phase 4-wire 120 to 480V, 50/60Hz. It Supports CTs from 100A to 5000A. Accurate to 0.5% (Class 0.5) The v.4 Omnimeters can also count the pulses from up to 3 different pulse output devices, as is explained in this video. These could be pulses from our Pulse Output Water and Gas Meters or from any other un-powered dry contact pulse output device. The real-time state of the three Inputs can also be polled remotely by ourEKM Push3 gateway. The Omnimeter data will return a High or Low state for each pin in real-time (use this for sensing switch states, open or closed doors, etc). The v.4 Omnimeters also include 2x controllable relay outputs. These can be controlled via RS-485, either locally via ourEKM Dash software, or remotely online via our Push3 gateway. You can set the outputs to be high or low to drive an external relay. The Relay Control Outputs can continuously provide up to 50 mA at 12 volts DC each. Control the EKM-Switch120 directly, or control lights, motors, entire buildings, implement Demand Response, Load Shedding, etc. via relay control. The Relay Control Outputs can also be set to go ON or OFF from 1 to 9999 seconds. The real-time state of the outputs can also be polled via RS485. The outputs can also be used to power an external device (Wireless 485Bee Module, sensors, etc).Relays can be controlled online when reading the meter with the EKM Push3 data system, or locally when reading the meter with a USB Converter. The only metering system that is commonly used that this meter will NOT support is 3-phase 3-wire 480 volts. You would need an Omnimeter HV v.4 for this system. These are only available "off menu" so please contact us if you would like more information about this meter model. This meter has been accuracy tested and certified by the State of California Department of Weights and Measures. It is California Type Approved and meets California standards for revenue grade metering. Many other states accept California Type Approval for their metering requirements. This meter uses our full range of compact Current Transformers (it cannot meter electricity without at least one). The CT ratio can be set internally to work with up to 5000 amp CTs (no multiplier needed). Use 1 CT for 120 volt single phase North American, or 230 volt 2-wire foreign systems Use 2 CTs for 120/240 volt single phase systems Use 2 CTs for 3-phase 3-wire systems (no neutral) Use 3 CTs for 3-phase 4-wire systems Easy clip-on DIN Rail Mounting. How to install an Omnimeter Pulse v.4: These meters are also supported by our revolutionary EKM Push3 system. This is our cloud-based, plug-and-play, meter data solution. We are really excited about this new system, and we recommend it for most remote reading applications that use our Omnimeter models. Push3 users can also take advantage of Encompass.io, which is our free online dashboard and meter management suite. Encompass.io Encompass.io is our free online meter management platform for monitoring data, managing meters, generating bills, and more. It is designed specifically for people who are remotely reading their meters via the Push3 system. This platform can be used to visualize data on customizable dashboards, visualize cost, monitor trends, group meters, and a lot more. Each meter and meter group in Encompass can also be set up to email you, and/or your tenant, PDF bills. Here is a sample PDF electric bill: EKM Widget The EKM Widget offers another option for quickly seeing your meter data online for Push3 users. It is also easy to save and share your Widget setting once you have it setup how you want. Here is an example: EKM Dash Our Omnimeters are also fully supported by our free, remote reading, EKM Dash software. If you want to read your Omnimeter on a computer locally, without the EKM Push3 system, then this software is what you would use. You will also need an EKM Blink USB Converter in order to do so. For more information about our products and services, we encourage you to visit our online Knowledge Base, which provides spec sheets, videos, tutorials, FAQs, diagrams, and more. Spec Sheet: Omnimeter Pulse v.4 Spec Sheet To better understand the differences between Omnimeter models you can download our Omnimeter and Communication Device Comparison Chart. INSTALLATION DIAGRAMS Single-Phase 2-Wire (Hot and Neutral) + Push3 Single-Phase 2-Wire (2 Hots, no Neutral) + Push3 Single-Phase 3-Wire (2 Hots and Neutral) + Push3 Three-Phase 3-Wire (3 Hots, no Neutral) + Push3 Three-Phase 4-Wire (3 Hots and Neutral) + Push3 Single-Phase 2-Wire (Hot and Neutral) + Push3 + 485Bees Single-Phase 2-Wire (2 Hots, no Neutral) + Push3 + 485Bees Single-Phase 3-Wire (2 Hots and Neutral) + Push3 + 485Bees Three-Phase 3-Wire (3 Hots, no Neutral) + Push3 + 485Bees Three-Phase 4-Wire (3 Hots and Neutral) + Push3 + 485Bees
Related
Related
Related
Related