Sprays are not available for international order. Please look to the liquid formulas Permalac Original is a protective, water-clear, fast-drying, solvent-based lacquer coating. It is a direct-to-substrate (DTS) coating, meaning it is designed to be applied to a myriad of surfaces directly without the use of a primer. Permalac’s state-of-the-art UV and corrosion inhibitors, as well as wide-ranging temperature stabilizers, assure endurance in the harshest conditions ranging from arctic freezing to desert heat, to beachfront salt air to acid rain. You can apply it to most metal, wood, or stone surfaces whether the surfaces are bare or painted. Permalac can behave as both a sealer (in case you decide to paint over it) or as a highly resistant topcoat, providing protection from all types of environmental corrosives. It has outstanding adhesion to a variety of substrates, including patinated and polished metals (copper, brass, bronze, steel, aluminum, zinc, etc.), hard woods, fiberglass, and masonry or stone products in both land and marine applications. On metals, Permalac is flexible and does not separate when the metal is bent. It also provides absolute protection for circuit breakers and other electrical components from molds and mildew, helping to avoid short-circuiting and other disruptive difficulties. Permalac can be sprayed or brushed on and, can be used in interior or exterior applications. It is available in either satin or matte sheens. Coverage is 400 square feet per gallon in a single coat. Physical PropertiesColor ClearGloss at 20/60 35.878 (on steel)Volume Solids 12.5%Weight Solids 14%Weight per Gallon 7.3 lbs.Coverage per Gallon 400 sq ftVOC 718 g/lDry Film Thickness 0.4-0.5 mils/coat*.75 mils*Recommended total dry mil thickness: 1.2 mils minimumPhysical Resistance (on steel)Adhesion (ASTM 3359 & Crosshatch test) 5BPencil Hardness (ASTM 3363) 4BTaber Abrasion Test 11.8 mg @ 300 cycles Flexibility (ASTM D522) Passed Mandrel Bending TestImpact (ASTM D2794) 160/80MEL Double Rubs (ASTM D4792) 10 Corrosion Resistance (ASTM B117, 5% NaCl spray)10= no rust, 0= rusted100 hrs. 200 hrs. 300 hrs.6 5 3UV resistance (ASTM 155 Cycle 1 Testing, xenon arc)After 1000 hrs., no visible degradation.Application CharacteristicsMix Ratio Full strength for brush, 4 to 1 for sprayingReducer #281 (standard), #69 (hot weather), #700 (0 VOC thinner)Cleaning Solvent Lacquer thinner or acetoneDry Time 10 minutes to touch dry, 20 minutes recoat.Cure Time 24 hours Application EquipmentHVLP spray gun, Cap tip 1.0, 15-20 PSISolvent-resistant brush*Disclaimer: All tests were done using Permalac Original Satin finish. It's expected thatPermalac Original Matte finish will perform to the same specification. Permalac NT is our most ecological formula, with under 70 g/l of VOCs! It does not contain toluene, has little to no odor, and demonstrates exceptional performance given its ultra-low VOC value. The Permalac NT provides excellent durability on steel, aluminum, brass, and bronze, as well as on other substrates such as stone, wood, and fiberglass. Our Permalac NT product has been FDA food-grade tested and holds a ClearChem certification in being compliant according to LEED standards. It is suitable for indoor and outdoor application. Permalac NT is available in semi-gloss, satin, matte, and ultra-flat sheens. Physical PropertiesColor ClearGloss at 20/60 35.878 (on steel)Volume Solids 9.5%Weight Solids 10%Weight per Gallon 7.7 lbsCoverage per Gallon 400 sq ftVOC
