Product Sheet Installation Manual A pre-assembled simplex lift station with Vortex impeller, capable of discharging wastewater from multiple fixtures. (220-240Volt/60hz). Powerful 1.5 HP motor ↑ 36 Ft (2'') or 20 Ft (4'') ↑ Vortex system designed to handle sanitary products and large diameter solids (2") Rated IP68 with external control and alarm Easy-access service panels The Sanicubic 1 VX is a 1.5 HP heavy duty simplex Vortex system used to pump away waste water from several bathrooms and fixtures from an entire building structure. This system is able to discharge the waste up to 36 feet vertical and/or 328 feet horizontal. It incorporates a Vortex system which is ideal for uncontrolled environments in both residential and commercial applications (ie. rental unit, offices, warehouses, etc). The Sanicubic 1 VX is designed to handle sanitary products that may have been flushed down the toilet; such may consist of condoms, sanitary napkins, q-tips, dental floss, etc. as well as large diameter solids This system consists of a 1.5-HP motor housed inside a compact but highly durable plastic enclosure. The motor has a high-performance grinding system and a fast-rotating cutting blade to reduce solids in the wastewater stream from toilets, tubs and showers, sinks, washing machines, dishwashers, etc. The Sanicubic 1 VX operation is as simple as the installation. The effluent enters the pump through one of four different inlets – one on either side of the unit at the bottom and two along the top. The inlets can accommodate 1-1/2” or 4” diameter pipes. As soon as the wastewater level reaches the trigger point, the pumping system activates. The effluent is then pumped out through 1-1/2” diameter rigid pipe connected on the top of the pump. Maximum pumping distances are 36 ft (2'') or 20 ft (4'') vertically and/or 328 Ft horizontally. The inside of the Sanicubic 1 VX comprises of a couple of pressure switches and a circuit board assembly, which starts and stops the unit, a powerful motor, which drive the Vortex impeller and the pump. The motor is sealed for life in an oil filled enclosure. A common spindle/shaft drives the impeller. The moving parts therefore are kept to an absolute minimum. Water, organic waste matter and solids that enter the enclosure are reduced and are picked up by the impeller mounted beneath the motor. The pump is able to handle up to 125 GPM (2'') or 137 GPM (4''). If the incoming rate is higher than the discharge rate, the pump automatically signals the “alarm” stage. This will activate the visual alarm on the pump’s external control panel and the audible alarm from the wired control box (if connected). The Sanicubic 1 VX can be retrofitted into an existing sewage ejector basin of at least 24” in diameter for a quick and easy pump exchange. As this is considered a “plug and play” device, no chains or floats are needed. Note that the effluent pipe leading into the pump has to be installed with the required ¼” per foot gravity flow. There must be a 11” height difference (from pump to connecting fixture) if the drain is connected to the bottom inlet. The wastewater from other sanitary fixtures is discharged into the Sanicubic 1 VX via three 1½-inch or 4” inlets, on either side of the housing and on the top of the enclosure. The internal discharge pipe comes equipped with a check valve that prevents back flow into the unit. Isolating valves (ball, gate valves) must be installed on waste inlets and on the discharge pipe to ensure that any service/maintenance may be carried out safely. This unit has been designed with a 2-1/2” vent connection on the top of the enclosure. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent. The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems. The Sanicubic 1 VX is IP68 rated for possible submergence which eliminates any potential water damage to internal components. It comes equipped with an external control panel as well as a visual and audible alarm system (15' long wire). The Sanicubic 1 VX has been certified to American and Canadian Standards. Macerating standard; US: CSA Certified - ASME A112.3.4, CA: Macerating Standard CSA B45.9. The Sanicubic 1 VX is ordered as a single unit only. No other fixtures are included. Connections Sink, Toilet, Shower/Bathtub, Urinal, Dishwasher, Laundry tub/Washing machine (sold separately)(Entire building structure) Specs Dimensions (Height x Width x Depth): 19-7/8" x 27-5/8" x 21-5/8" Weight 68 lbs. Inlets (in) 1 1/2'' (side) 4" (top) Power supply 240 V - 60 Hz Noise level (measured at 3 ft.) ≤ 70 dBA Horizontal discharge 328 ft Vertical discharge 36 fr (2") or 20 ft (4") Amperage (Amps) 12 A Max Operating maximum temperature 158 F° Discharge pipe diameter 2" or 4" Tank volume 15.9 gallons Method of activation Pressure switch/circuit board Discharge rate at 3 ft 125 gal/min (473 liters/min) (2") or 137 GPM (518 liters/min) (4'') Discharge rate at 36 ft 26 gal/min (98 liters/min) (2") or 90 GPM (340 liters/min) (4'') Motor 1 HP oil-filled thermally protected motor Capacitor rating (microfarad) 30 Power cord length (in) 98 Shut off head (ft) 43 Normal running time Depends on number of fixtures Toilet, Shower/bathtub base min height (in) 11 Certifying agencies CSA (IPC, NSPC)
