These products are all Made to Order Which means they are non-cancelable and non-refundable. Minimum Order Quantities May Apply Description Solid Braid Nylon Rope with Galvanized Aircraft Cable Core This premium Solid Braid Nylon rope is available in the following sizes: #6, #8, #10, and #12. This solid braid nylon with galvanized aircraft cable core, solid braid construction stays round over pulleys. The wire center is ideal for flag pole halyards. Most sizes are supplied in the following diameters in inches: 3/16", 1/4", 5/16", and 3/8". The available lengths in feet are 500' and 1,000' with a wire size in inches of either 1/16" or 3/32", and are supplied on a durable wooden spool. Features Features Solid braid construction stays round over pulleys. Wire center ideal for flag pole halyard Specifications Download Spec Sheet Solid Braid Nylon Pulling Rope with Galvanized Aircraft Cable Core Size Diameter (Inches) Length (Feet) Wire Size (Inches) Approximate Package Weight (Lbs) #6 3/16 1,000 1/16 15 #8 1/4 1,000 3/32 30 #10 5/16 500 3/32 19 #10 5/16 1,000 3/32 38 #12 3/8 500 3/32 24 #12 3/8 1,000 3/32 48 Additional Information WARNING: MISUSE COULD LEAD TO SERIOUS INJURY CAUTION: Use of Working Loads Because of the wide range of rope use, rope condition and exposure to the various factors affecting the rope, it is impossible to make blanket recommendations for the correct choice of rope. However, we have provided the tensile strength for each diameter and type of rope. These strengths are based on tests of new and unused rope, with appropriate splices. Proper choice, care and inspection of the rope are essential for reasonably safe use. Consult your cordage vendor for proper use. Dynamic Loading Voids Normal Work Loads Dynamic Loading occurs when rope is subjected to sudden or extreme stress. Figures given as working loads are void if rope has been subjected to dynamic loading, high temperatures, long periods of load, extreme stress, improper storage. Effect of Temperature on Tensile Strength The tensile strength charts apply to ropes tested at normal room temperature (70°F). Ropes have lower tensile strength at higher temperatures. Continued exposure at elevated temperatures causes permanent damage. Avoid Abrasion All ropes should be protected against sharp edges and abrasive surfaces. When worn areas are visible, the tensile strength is compromised. Protect the rope's surface with chafing gear around the rope. Avoid Chemicals Acids and Alkalis are damaging to ropes and fibers. Caution should be used when ropes are used around building cleaning acids, cast soda and paints. Proper inspection should be made of rope prior to use. Rope Inspection Rope Inspection should be a continuous process that takes place before, during and after each use. When fiber shows wear in any given area, the rope should be re-splices, downgraded or replaced. Knots and Splicing Splicing should be used instead of knots. Knots can decrease a rope's tensile strength by up to 50% Rope Storage All ropes should be stored in a clean dry location, out of direct sunlight and extreme heat. Natural fiber ropes, if not kept dry, will rot over time, reducing tensile strengths dramatically. Sunlight Degradation Polypropylene and polyethylene ropes are subject to ultraviolet degradation. The product should be replaced when signs of excessive deterioration is indicated by discoloration or broken filaments. Tensile strengths may be dramatically reduced by sunlight degradation. Dielectric Properties Dielectric property testing applies only to new, unused clean rope and holds true only under these ideal conditions. Dirt, grease, entrapped moisture, or other contaminants will increase conductivity greatly. Nylon or natural fiber ropes would not be used around energized lines. Rope dielectric properties must be tested under actual operation conditions. What's in the Box What’s in the Box Qty 1 - Solid Braid Nylon Pulling Rope with Galvanized Aircraft Cable Core
