Description Lepus Mounting Plates Camera-Specific Mounts for the Lepus Telecompressor The Lepus telecompressor has a design back-focus distance of 100mm on-axis. Each of the camera mounting plates below are designed to maintain that back-focus for the best overall image quality and a reduction of 0.62X. Varying the back-focus distance will alter the magnification (reduction) but may introduce undesirable optical aberrations as well. We recommend using the Lepus telecompressor only with the recommended camera-specific mount. Each camera mount consists of a 2.1" ID tube of various lengths and a mechanical interface such as a T-thread, C-mount, or STL thread. This ID tube fits over the camera side of the Lepus telecompressor, which features the OPTEC-2100 male circular dovetail mount. The camera mount is held securely to the Lepus dovetail using three oval point setscrews located 120 degrees apart. It is important that the overall back-focus distance be set as closely as possible to the design distance of 100mm on-axis. Measured from the flange at the bottom of the OPTEC-2100 dovetail, the distance works out to 105mm as shown in the PDF at left. Most of the mechanical camera interfaces require an additional 1/10th inch or 2.5mm of back-focus. The camera back focus distance, BF, should be known to within about 1mm for best performance and should include the thickness of any filter wheel, off-axis guider or other adapter between the Lepus and camera sensor. Use the table below to find the appropriate mounting plate for many commercially available cameras and configurations. If your camera is not listed below and you know the optical back-focus, BF, and mechanical interface (i.e. T-thread) you can determine the stock number as with the following calculation: TUBE LENGTH = 105mm - FLANGE THICKNESS - CAMERA BACK-FOCUS Mechanical Interface Flange Thickness Stock No. Prefix T-thread 2.5mm #19392 Pentax thread 2.5mm #19395 SCT thread 2.5mm #19396 STL 2.156" thread 2.5mm #19398 C-mount 2.5mm #19399 Canon and Nikon DSLR requires T-threadand brand specific bayonet mount. varies withbayonet #19392 Next use the TUBE LENGTH value calculation above for the suffix. For example, nearly all C-mount cameras share a 17.5mm BACK-FOCUS value. The C-mount stock number prefix is #19399 and the TUBE LENGTH would be equal to 105mm - 2.5mm - 17.5mm = 85mm. The Optec stock number for a C-mount camera would therefore be #19399-85 as shown in the table below. NOTE: The minimum tube length is limited by the height of the OPTEC-2100 dovetail plus the press-flange of the mechanical mount (usually about 0.2" or 5mm). The standard Lepus telecomprssor minimum tube length is 15mm while the Edge HD specific Lepus telecompressor is 17mm. Specifications Camera Type Tube Length (mm) Thread Stock No. Any C-mount camera with standard lens mount 85 C 19399-85 Any CS-Mount Camera 90 C 19399-90 Apogee D02 Housing - U47, U77, U4000, U8300 std. body 76 SCT 19396-76 *Apogee D02 Housing - U9, U10 std. camera 75 SCT 19396-75 *Apogee D06 Housing - U6, U9, U10, U4000 camera 89 SCT 19396-89 Atik Instruments 4000/*11000 88 T 19392-88 Atik Fira M1 motorized filter wheel 83 SCT 19396-83 *Canon DSLR Camera - Canon bayonet mount 47 T plus bayonet 19392-47C Fishcamp Starfish 91 T 19392-91 Meade Deep Sky Imager 94 T 19392-94 Meade Deep Sky Imager with RGB filter bar 77 T 19392-77 *Nikon DSLR Camera - Nikon bayonet mount 46 T plus bayonet 19392-47N Orion StarShoot Pro 82 T 17482-82 QSI 504 full body camera with filters 67 T 19392-67 QSI 504 full body camera without filters 67 T 19392-67 QSI 504 medium body camera without filters 79 T 19392-79 QSI 504 slim body camera with filters 88 T 19392-88 QSI 516, 532 full body camera with filters 67 T 19392-67 QSI 516, 532 full body camera without filters 67 T 19392-67 QSI 516, 532 medium body camera without filters 80 T 19392-80 QSI 516, 532 slim body camera without filters 88 T 19392-88 QSI 516WSG camera with Off-Axis guider and no filters 52 T 19392-52 QSI 52mm Spacer tuber with clearance for QSI WSG Pick-Off Mirrir 52 T 19392-52QSI QSI 516WSG camera with Off-Axis guider and filters and standard T-thread. Note: T-thread mount must be turned down for clearance of the OAG. 53 T 19392-53Q QSI 583WSG camera with Off-Axis guider STL 2.156x24tpi thread 49 STL 19398-49 QSI 520 full body camera with filters 67 T 19392-67 QSI 520 full body camera without filters 67 T 19392-67 QSI 520 medium body camera without filters 80 T 19392-80 QSI 520 slim body camera without filters 88 T 19392-88 SBIG ST-7/8/9/10/2000 with CFW-10 filter wheel mounted directly on camera without face plate and with D-block 62 T 19392-62 SBIG ST-7/8/9/10/2000 with CFW-8/8A/9 with new 0.25 inch thick front plate on camera and no D-block 59 T 19392-59 SBIG ST-7/8/9/10/2000 new 0.25 inch thick front plate and D-block with T-Thread 77 T 19392-77 SBIG ST-2000XCM with AO-8 24 T 19392-24 SBIG ST-8300 85 T 19392-85 SBIG ST-8300 with CFW5/8-8300 64 T 19392-64 *SBIG STL with 3mm thick filters 65 STL 19398-65 *SBIG STL without filters 64 STL 19398-64 *Starlight Xpress SXVF-H9 camera plus filter wheel 62 T 19392-62 Starlight Xpress SXV-H9 T-thread camera 84 T 19392-84 Starlight Xpress SXV-M25C camera 84 T 19392-84 QHY-8 camera (T-mount depth to IR Filter=0.160" 81 T (short) 19392-81 QHY-8L camera 82 T 19392-82 QHY-8Pro camera (without "tile adjust ring", add 3mm to BF for ring) 84 T 19392-84 QHY-8 camera with Orion SteadyStar 41 T 19392-40 QHY-9 camera 102 T 19392-102 QHY-9 camera with 2" color filter wheel 46 T 19392-46 QHY-10 camera 82 T 19392-82 Older Camera Mounts SBIG ST-7/8/9/10/2000 with CFW-8/8A/9 filter wheel with old 0.20 inch thick front plate and no D-block 60 T 19392-60 SBIG ST-7/8/9/10/2000 with old 0.20-inch thick front plate on camera and D block with T-thread 78 T 19392-78 * denotes vignetting may occur with Lepus telecompressor.
