The Tacki-Mac Bubble Replacement is a thin wrap grip made for TaylorMade bubble shafts. Its .810" core is a much larger opening than a regular grip, so it fits shafts with a .810" butt. Tacki-Mac lists it at 32 g (±2 g), latex free. It is a standard size grip, not an oversize: the wall is thinner, softer and stretchier, so once it is on the shaft it feels close to a standard grip. You will need the Ultimate Grip Installer Tool to install it. Not sure which bubble grip you need? Measure the butt end of your shaft. A .810" butt takes the Bubble Replacement; a butt up to .865" takes the Pro Lite 865. Our bubble grip guide explains the difference. Who It's For Good fit if you... Have TaylorMade bubble shafts, or any shaft with a .810" butt Want to keep playing an older bubble-shaft club Want a standard-size feel on a wide shaft butt Need a latex-free grip: Tacki-Mac says this grip is latex free Not the right fit if you... Have a regular .600" or .580" shaft: browse our standard size grips Have a bubble shaft wider than .810" (up to .865"): choose the Tacki-Mac Pro Lite 865 Bubble Want an oversize grip on a bubble shaft: this grip installs at a standard size Do not want to buy an installer tool: you need the Ultimate Grip Installer Tool to fit it How It Plays Big core, thin wall. Tacki-Mac makes the grip with a .810" core, a much larger opening than the .600" or .580" of a regular grip. The wall is thin, so the finished grip ends up close to a standard size on a bubble shaft. Stretches on. Bubble grips are softer and stretchier than regular grips. They stretch to fit as you install them with the Ultimate Grip Installer Tool. Wrap surface. Tacki-Mac describes it as an all-black wrap with no paint fill. Specifications Spec Bubble Replacement .810 Brand / model Tacki-Mac Bubble Wrap Grip for TaylorMade bubble shafts Size Standard once installed (not oversize) Core size .810" Weight 32 g (±2 g) Length 10 1/4" Material Thermoplastic rubber, latex free Surface Perforated wrap, black, no paint fill Fits Shafts with a .810" butt, such as TaylorMade bubble shafts Part number 105b-810tm Core, weight, length, latex free and finish from Tacki-Mac's official product page and its answers on that page, checked October 2026. Size, material and perforated surface from our previous listing. Part number is our SKU. How It Compares to Other Tacki-Mac Grips Bubble Replacement (this grip) Pro Lite 865 Bubble Perforated Tour Pro Wrap Standard Fits shaft butt .810" Up to .865" Regular shaft Core .810" .865" .600" or .580" Weight 32 g (±2) 18 g (±2) 51 g (±2) Installer tool needed Yes Yes No Core and weight from Tacki-Mac's own product pages. Installer tool from our listings. Buying for a Full Set Regripping a full set? Get the Bubble Replacement 13-grip kit with installation supplies, and add the Ultimate Grip Installer Tool if you do not have one. Our Grip Installation Kit includes 14 tape strips plus grip solvent, and our bubble grip guide covers measuring and fitting. Browse all bubble grips. Frequently Asked Questions Do I need a special tool to install it? Yes. To put a bubble grip on a bubble shaft you need the Ultimate Grip Installer Tool. It opens up the grip so it slides over the wide butt without splitting. Use plenty of solvent inside the grip over the tape, or the grip can stick halfway on. Our step-by-step regripping guide covers the rest of the job. Will it fit my bubble shaft? It fits shafts with a .810" butt, which is the TaylorMade bubble shaft size Tacki-Mac makes it for. Measure the butt end before you order. If it is wider, up to .865", choose the Pro Lite 865. Is it an oversize grip? No. It is a standard size grip. The core is larger to fit the shaft, but the wall is thinner, so the outside ends up close to a standard grip. How much does it weigh? 32 g, plus or minus 2 g, per Tacki-Mac. Tacki-Mac gives its length as 10 1/4". Can I use it on a regular shaft? No. The .810" core is far too large for a regular .600" or .580" shaft. Browse our standard size grips instead.
Related
Related
Related
Related