FLYABLE ACTIVE BASSREFLEX SUBWOOFER 3200W RMS DIGIPRO® G4 AMPLIFIER 143 dB MAX SPL USABLE BANDWIDTH [- 6 dB]: 28 Hz to cut frequency DANTE & A2NET READY LF: 2 x 18”, 4” v.c. - NEODYMIUM Weight: 100Kg (220 lbs) Packed with exclusive technologies, VIO S218F widens the possibilities for low frequency reproduction in larger VIO sound reinforcement deployment. SKY IS THE LIMIT With this system version, you can extend the range of action of the distinctive VIO S218 subwoofer by flying an array of VIO S218F in the air. Up to 14 cabinets can be flown with a single DRK-218F flybar. TOUR-READY The most demanding sound reinforcement application for touring requires extreme flexibility in order to accommodate the specific needs for every event in any venue worldwide. VIO S218F is the perfect bottom-end addition to large VIO deployments, packing astounding sound performance and a ultra low frequency punch, extending down to 28Hz. CARDIOID PRESET A cardioid preset button automatically process the sound of the backward sub in gradient inverted stack configurations, in order to reach maximum cancellation of the rear side. You can easily fly VIO S218 in inverted orientations, according to the desired backward rejection. An easy cable run carved out will allow all the cables to run smoothly through the cabinets for a clean cable management. REAL-TIME CONTROL As a default, VIO S218F is equipped with dBTechnologies RD-Net card, for real time remote control via Aurora Net software. Furthermore, the preamplifier is ready for future upgrades with Audinate DanteTM AoIP protocol. To help users in this configuration, S218F comes with built-in technologies: Near Field Communication (NFC™) proximity sensors are used to determine the position of each box within an array. This technology, together with a hi-brightness LED bulb on the front of the enclosure, contributes to help the user to recognize, identify and match each box physical position on the remote control software Aurora Net. The amp also allows users to run auto-test on electronics and transducers before and after use and a real time impedance control. This unique system ensure tour-grade reliability and remote control over your entire PA’s health. Technical Data Speaker Type Flyable Active Bassreflex subwoofer Acoustical data Frequency Response [- 10 dB] 27 Hz (HPF) Frequency Response [- 6 dB] 28 Hz to cut frequency (Xover dependent) Max SPL 143 dB LF 2x18” Neodymium Voice Coil LF 4” Directivity Omnidirectional Amplifier 3200 W RMS [2x 1600 W RMS Class-D Digipro® G4] Cooling Passive convection, internal fan Power Supply Full-range SMPS with PFC (100V~-240V~, 50-60Hz) Processor Controller DSP 32 bit AD/DA Converter 24 bit/96 kHz Limiter Peak, RMS, Thermal Delay Option 0 - 9.9 ms internal | steps of 0.1 ms [on-board] Crossover Frequency LF-HF Selectable 60-110 Hz + Full Range (8 steps) LF-Xover out slope 24 dB/Octave Input Signal Input 1x XLR balanced 1x USB Data Service Signal Output 1x XLR balanced Network RDNet Card (1x RJ45 IN 1x RJ45 Link) Dante Card [Optional] Power Socket 1x PowerCON TRUE1 In 1x PowerCON TRUE1 Out Controls 1x Input Attenuation Rotary Encoder 2x Delay Rotary Encoder (0-9.9 ms) 1x Polarity Inversion Switch (0° or 180°) 1x Cardioid mode Switch 1x X-Over Frequency Rotary Encoder (8 steps) Special Features NFCTM and Frontal LED Identification System 380V Resistant SMPS IPOS Intelligent Power-On Sequence Opto-isolated floating pre-amp System Test (transducers diagnostics) Mechanics Housing Multiplex plywood - Polyurea painting Handles 2x Side. Aluminium Raincover Included Rigging Points side integrated rigging hardware, 2x Pick Points on top for DRK-210 rigging frame Width 1300 mm (51.18 in) Height 520 mm (20.47 in) Depth 800 mm (31.5 in) Weight 100 kg (220 lbs) Notes: The data are not binding; dBTechnologies reserves the right to modify the data at any time and without previous notice.**AES75: @1 meter, free field, with Music-Noise
