Description This part is responsible for letting water into the washing machine. These parts might need replacement if your washer is not filling properly, or if it isn’t filling at all. Cross Reference Information:WPW10144820, W10144820, W10284557, PS11749042, W10311458, WPW10144820VP, B005AR7WZY, B004A5V9RE. Quality you can Trust! All Snap Products are made with premium materials and are tested so they last. Compatible with the following Washer brands: Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. Customer Support: Should you not find your part number listed or need assistance with model compatibility, our customer service team is ready to help with a model lookup, ensuring you get the right part for your unit. Contact us at [email protected] or via phone at 1-802-727-4126 *NOTE: Just because parts look the same does not mean that they are the same. Use the model numbers below to ensure that this part is compatible with your appliance or contact us directly to ensure this part is compatible with your unit! Model Numbers Use ctrl+F then enter your model number in search bar and hit enter 11018812701 11020522900 11028222701 11029422801 11029432801 11029442801 11029522801 11029532801 11029592801 11029622801 11029632801 11029672801 11029682801 11029692801 11029722801 11029727801 11029732801 11029737801 1105062110 1CWTW5200VQ1 1CWTW5300VW1 1CWTW5505VQ1 1CWTW5590VQ1 1CWTW5790VQ1 ATW4475VQ0 ATW4475VQ1 ATW4475XQ0 CAWS14234VQ0 CAWS16445VQ0 CAWS16445WQ0 CAWSS16445WQ0 CSWS16445WQ0 ETW4400WQ0 ETW4400WQ1 ETW4400XQ0 ITW4300XQ0 IV46001 IV4600X0 IV48001 IV4800X0 MVWC300VW1 MVWC400VW1 MVWC450WW0 MVWC500VW1 MVWC700VJ1 MVWC700VW1 NTW4500XQ0 NTW4600VQ1 NTW4600XQ0 NTW4800VQ1 NTW4800XQ0 NTW4880YQ0 RTW4305VQ1 RTW4305VQ2 RTW4305XQ0 RTW4440VQ1 RTW4440VQ2 RTW4440XQ0 WTW5200VQ2 WTW5300VW2 WTW5300VW3 WTW5310VQ0 WTW5505VQ1 WTW5510VQ0 WTW5590VQ1 WTW5600VQ0 WTW5790VQ2 Installation Instructions Installation Instructions for W10144820 Tools Needed: Screwdriver Putty knife (depending on style) Flat head screwdriver Needle nose pliers Unplug appliance and/or turn off circuit breakers to prevent electrocution. Turn off hot and cold-water supply. Place a towel on the floor in case of leakage. Disconnect the fill hoses by loosening them with pliers and then by hand. Make sure to know which one is hot and cold. Next, is removing the console. There are three types of styles. One, has two Philips screws in the back that you must unscrew. Another one, has a trim piece on the side of the console that you must pop off and the screws are located at the top and front of the console, on each side. The last style, has a clip on each side under the console, in which you must use a putty knife in order to remove. Once console is out, carefully swing it back. Next, remove the clips that secure the cabinet to the back wall. Remove the lid switch wire harness. Next, remove the cabinet off the frame by lifting the lid, grabbing the inside with one hand, tilt the body at a 45-degree angle and lift it off the frame. Set aside. Disconnect the wire harness of the water inlet valve. Run the wire harness around the air pressure hose and with needle nose pliers remove the retainer that holds the wire harness; it is located in the rear of the machine. Press on the tabs and slightly push forward. Next, is removing the water inlet valve. Lift the valve up and rotate it to release. To install the new valve assembly, place the valve inside the slots of the wall. Place the wire harness back to the wall, route the wire harness underneath the air pressure hose, and reconnect wire harness. Place the cabinet back in the machine the same way it came off. Make sure the plastic strips on the rear are properly aligned. Next, place the clips that secure the cabinet to the back wall by placing the tab on the slot of the back wall and snap the other side to the cabinet. Reconnect the lid switch wire harness. Swing back the console making sure tabs went into the slots, usually there is a locking sound. Reattach the console the same way it was taken off. Finally, reconnect the fill lines making sure they are placed properly, cold line with cold and hot with hot. Tighten them with pliers. Turn on water supply, plug in appliance and installation is complete.
Related
Related
Related
Related