W5500-EVB-Pico is a microcontroller evaluation board based on the Raspberry Pi RP2040 and fully hardwired TCP/IP controller W5500 – and basically works the same as Raspberry Pi Pico board but with additional Ethernet via W5500. Features RP2040 microcontroller with 2MByte Flash Dual-core cortex M0+ at up to 133MHz 264kByte multi-bank high performance SRAM External Quad-SPI Flash with eXecute In Place (XIP) High performance full-crossbar bus fabric 30 multi-function General Purpose IO (4 can be used for ADC) 1.8-3.3V IO Voltage (NOTE. Pico IO voltage is fixed at 3.3V) 12-bit 500ksps Analogue to Digital Converter (ADC) Various digital peripherals 2 × UART, 2 × I2C, 2 × SPI, 16 × PWM channels 1 × Timer with 4 alarms, 1 × Real Time Counter 2 × Programmable IO (PIO) blocks, 8 state machines total Flexible, user-programmable high-speed IO Can emulate interfaces such as SD Card and VGA Includes W5500 Supports Hardwired Internet Protocols: TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE Supports 8 Independent Hardware SOCKETs simultaneously Internal 32 Kbytes Memory for TX/ RX Buffers Supports High Speed Serial Peripheral Interface(SPI MODE 0, 3) Micro-USB B port for power and data (and for reprogramming the Flash) 40 pin 21x51 'DIP' style 1mm thick PCB with 0.1" through-hole pins also with edge castellations 3-pin ARM Serial Wire Debug (SWD) port 10 / 100 Ethernet PHY embedded Supports Auto Negotiation Full / Half Duplex 10 / 100 Based Built-in RJ45 Built-in LDO Pin-out W5500-EVB-Pico pinout is directly connected to the GPIO of RP2040. It has the same pinout as the Raspberry Pi Pico board. However, GPIO16, GPIO17, GPIO18, GPIO19, GPIO20, GPIO21 are connected to W5500 inside the board. These pins enable SPI communication with W5500 to use Ethernet function. If you are using the Ethernet function, these pins cannot be used for any other purpose. The RP2040 GPIO used inside W5500-EVB-Pico is as follows. I/O Pin Name Description I GPIO16 Connected to MISO on W5500 O GPIO17 Connected to CSn on W5500 O GPIO18 Connected to SCLK on W5500 O GPIO19 Connected to MOSI on W5500 O GPIO20 Connected to RSTn on W5500 I GPIO21 Connected to INTn on W5500 I GPIO24 VBUS sense - high if VBUS is present, else low O GPIO25 Connected to user LED I GPIO29 Used in ADC mode (ADC3) to measure VSYS/3 Apart from GPIO and ground pins, there are 7 other pins on the main 40-pin interface: Pin No. Pin Name Description PIN40 VBUS Micro-USB input voltage, connected to micro-USB port pin 1. Nominally 5V. PIN39 VSYS Main system input voltage, which can vary in the allowed range 4.3V to 5.5V, and is used by the on-board LDO to generate the 3.3V . PIN37 3V3_EN Connects to the on-board LDO enable pin. To disable the 3.3V (which also de-powers the RP2040 and W5500), short this pin low. PIN36 3V3 Main 3.3V supply to RP2040 and W5500, generated by the on-board LDO. PIN35 ADC_VREF ADC power supply (and reference) voltage, and is generated on W5500-EVB-Pico by filtering the 3.3V supply. PIN33 AGND Ground reference for GPIO26-29. PIN30 RUN RP2040 enable pin, To reset RP2040, short this pin low. Operation Condition Item Description Operation Temperature MAX 85C (including self-heating) Operation Temperature MIN -20C VBUS DC 5V (+/- 10%) VSYS Min DC 4.3V VSYS Max DC 5.5V Recommended maximum ambient temperature of operation is 70C. Technical Reference RP2040 Datasheet W5500 Datasheet Schematic Schematic & Part list & Gerber File Dimension (Unit : mm) Firmware Example Please refer to below links to find firmware example. C/C++ Examples CircuitPython Examples MicroPython Examples AWS Examples Azure Examples FreeRTOS Examples LwIP Examples
