MORE ON ORDER-MESSAGE US FOR AN ETA High input capacity and fader count makes this powerful console ideal for larger applications. 33 motor faders (32 channels + 1 master) 48 input mixing channels (40 mono + 2 stereo + 2 return) 20 Aux (8 mono + 6 stereo) + Stereo + Sub buses 8 DCA groups with Roll-out 32 analog XLR/TRS combo mic/line inputs + 2 analog RCA pin stereo line inputs 16 analog XLR outputs 34 x 34 digital record/playback channels via USB 2.0 + 2 x 2 via a USB storage device 1 expansion slot for NY64-D audio interface card Specs Outline Fader Configuration 32 + 1 (Master) Mixing Capacity Input Channels 48 (40 mono + 2 stereo + 2 return) Aux Buses 20 (8 mono + 6 stereo) Stereo Buses 1 Sub Buses 1 Input channel functions 8 DCA Groups I/O Inputs 32 mic/line (XLR/TRS combo) + 2 stereo line (RCA pin) Outputs 16 (XLR) Expansion slots 1 On-board processors DSP 8 Effects + 10 GEQ USB 34x34 USB Audio Interface, 2-track recording via USB Storage Device General specifications Sampling frequency rate Internal 48 kHz Signal delay Less than 2.6 ms, INPUT to OMNI OUT, Fs=48 kHz Fader 100 mm motorized, Resolution = 10-bit, +10 dB to –138 dB, –∞ dB all faders Total harmonic distortion Less than 0.05% 20 Hz–20 kHz @+4 dBu into 600 Ω , INPUT to OMNI OUT, Input Gain=Min. (Measured with a –18 dB/octave filter@80 kHz) Frequency response +0.5, –1.5 dB 20 Hz–20 kHz, refer to +4 dBu output @1kHz, INPUT to OMNI OUT Dynamic range 110 dB typ., DA Converter, 107 dB typ., INPUT to OMNI OUT, Input Gain=Min. Hum & noise level Equivalent input noise –128 dBu typ., Input Gain=Max. (Measured with an A-Weight filter) Residual output noise –85 dBu, ST master off (Measured with an A-Weight filter) Crosstalk –100 dB (Measured with a –30 dB/octave filter@22 kHz), adjacent INPUT/OMNI OUT channels, Input Gain=Min. Power requirements 100–240 V 50/60 Hz Power consumption 120 W Dimensions W 866 mm (34.1in) H 225 mm (8.9in) D 599 mm (23.6in) Net weight 20.0 kg (44.1lb) Accessories Quick Guide, Power Cord, CUBASE AI download information Options Expansion Card, Foot Switch (FC5) Others Operating temperature range: 0–40 °C, Storage temperature range: -20–60 °C Analog input characteristics Input Terminals GAIN Load Impedance For Use With Nominal Input Level Connector balanced / Unbalanced Sensitivity*1 Nominal Max. before clip INPUT1-32 +66dB 7.5KΩ 50-600Ω Mics or 600Ω Lines -82dBu (61.6V) -62dBu (0.616mV) -42dBu (6.16mV) Combo Jack (XLR-3-31 type *2 or TRS phone *3) Balanced -6dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V) ST IN 1,2 — 10kΩ 600Ω Lines -30dBV (31.6V) -10dBV (316mV) +10dBV (3.16V) RCA Pin Jack Unbalanced *1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.) *2. 1: GND, 2: HOT, 3: COLD*3. Tip: HOT, Ring: COLD, Sleeve: GND*In these specifications, 0dBu = 0.775Vrms. *+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch. Analog output characteristics Output Terminals Source Impedance For Use With Nominal GAIN SW Output Level Connector balanced / Unbalanced Nominal Max. before clip OMNI OUT 1-16 75Ω 600Ω Lines “+24dBu” position (default) +4dBu (1.23 V) +24dBu (12.3 V) XLR-3-32 type *1 Balanced PHONES *3 100Ω 40Ω Phones — 3mW 75mW Stereo Phone Jack (TRS) *2 Unbalanced *1.1: GND,2: HOT, 3: COLD *2 Tip: LEFT, Ring: RIGHT, Sleeve: GND *3 The position of the level control is lowered by 16dB from the maximum.*In these specifications, 0dBu = 0.775Vrms. *All output DA converters are 24bit, 128times oversampling. Digital input/output specifications Terminals Format Data length Audio Connector USB (TO HOST) USB 24bit 34ch input / 34ch output, PCM USB (B type) iPad USB — Playback: MP3 or WAV file data / Record: WAV file data USB (A type) Control I/O specifications Terminals Format Level Connector NETWORK IEEE802.3 10BASE-T/100Base-TX RJ-45 FOOT SW — — TS Phone
