The Rotary FD6166-5 lifting cable is the direct replacement for the Rotary lift it came off of. Cross-referenced as ALS-9763-66, it is the genuine Rotary part — same part number, same fit, and same working specification as the one already on your lift. Ordering the Rotary lifting cable from us gets you the OEM piece that matches the lift, not an aftermarket knock-off that is close but not the same. Specifications Part number: ALS-9763-66 Brand: Rotary Type: Genuine OEM lifting cable A cable is only as good as the sheave it rides. The two parts wear as a system: a grooved or wobbling sheave chews the cable, and a corded cable grinds a fresh sheave. That's why techs who pull a lift apart for one usually replace both, along with the small lock-release cable that trips the pawls. Swapping a cable onto worn sheaves just starts the failure clock over again. Cable failure almost never happens all at once. A strand pops here, a groove wears oversize there, a sheave bushing walks out the side, and the cable starts cording where it turns. Left alone, the frayed section keeps losing strands until the day it lets go — usually with weight on the lift. That is the whole reason these tension parts get inspected and swapped on a schedule instead of run to failure. Related parts for this lift The parts below are commonly ordered alongside this one — cables, sheaves, seals, and hardware wear on similar schedules, and most repairs go faster when the whole set is done in one visit. Cable Assembly x 23' $ 1,251.64 $ 1,126.48 - Rotary - FD6166-3 Cable Assembly $ 1,093.33 - Rotary - FD6165 Cable Assembly - Rotary - FD6166-4 Replacing your lifting cable Cable and sheave replacement usually happen together, since a worn sheave will chew a fresh cable and a bad cable scores a new sheave. Plan on inspecting and, if needed, replacing both while the lift is open, then equalizing the cables so the locks land together. It's methodical work with a clear right way to do it, laid out in full in the step-by-step guide. Full step-by-step: how to replace 2-post lift cables. Find the right part for your lift The surest way to get the right part is to work from your lift's own breakdown. open our Rotary parts lookup, choose your model, and every part is mapped on the drawing with its number and price. If you cannot find the model plate, our guide to finding your model number explains where each lift type hides it, and our phone line is open if you want a hand. Signs a cable or sheave is worn out Kinks are a hard stop. A cable that has ever been kinked has permanently damaged strands at the bend, even if it looks fine now, and it will fail there. Look for kinks, kinks that were straightened back out (you'll see a slight flat), and any spot where the cable rubbed a bracket and wore a shiny flat. Worn flats and kinks both condemn the cable. Parts commonly replaced at the same time Order the companions now, not later. A cable job is the right time to refresh sheaves, pins, and the lock-release cable, since the hard part — getting into the columns — is already done. Give us your lift's model and serial and we will put together the full wear kit so nothing is left half-finished. Safety notes A worn cable gives warning — a strand here, some cording there — and a shop that ignores those warnings is the one that has a bad day. Inspect at every service, replace before the interval if you see damage, and never trust a slack or kinked cable back into service. Set the lift on its locks before touching anything. Before you order Ordering tip: cables come in specific lengths and end styles per lift and height variant, so read the numbers off your data plate before you buy. If you are replacing a set, order the set — and if a sheave is grooved, add it now while the lift is open rather than making a second trip. Ordering the right revision Before this goes in the cart, grab two things off your lift: the model number and the serial number, both on the manufacturer's plate. The serial matters more than most people expect — lift makers revise components between production runs without renaming the lift, and the run your serial falls in determines which revision of this part is correct. If you are working from a failed part rather than a plate, measure what you have and photograph how it mounts. Send that to us along with the lift brand, and we will check it against the same parts breakdowns our own techs use in the field before you commit to the order. Why buy your Rotary lifting cable from Auto Lift Services We install, inspect, and repair Rotary lifts every week — the ALS-9763-66 is a part we handle in the shop, not a random SKU we drop-ship. The phone answers if you have a question mid-install — call 800-674-9302 — and every part ships genuine, no aftermarket substitution unless you ask for it.
Related
Related