Get Your Pool Ready for a Fresh New Look with Ramuc Pool Paint Clean & Prep Solution. Ramuc Clean & Prep Solution is a versatile product used to prepare various pool surfaces for painting. It is used to clean and degrease while simultaneously dissolving mineral deposits, and increasing porosity for good adhesion on surfaces before painting. This pool cleaner solution can be used on painted surfaces, bare plaster, concrete, or fiberglass. It is safe to use near plants or grass, and excellent for filter element cleaning. Features Specs Application Guide Why Choose Ramuc Clean and Prep Solution? Versatile Use: Ramuc clean & prep solution can be used on painted surfaces, bare plaster, concrete, or fiberglass. Surface Preparation: Efficiently cleans and degreases while dissolving mineral deposits to increase porosity for good adhesion. Safety: VOC compliant, odor and fume-free, water-rinse neutralized, and biodegradable. Eliminates Need for Harsh Chemicals: Replaces TSP/Acid Etch/TSP, making surface preparation easier and less hazardous. Coverage: 1 gallon prepares approximately 400 sq. ft. of bare concrete, Marcite, Gunite, and plaster surfaces or 600 to 800 sq. ft. of bare fiberglass and painted surfaces. Have Questions? Check our FAQ section or contact us for more information about Ramuc Clean and Prep Solution. Ramuc Clean and Prep Spec Chart: Title Specs Installation Temperature: 10° C (50° F) min / 29.4° C (85° F) max Number of Coats Required: Recoat Time: Full Cure: Coverage: 400 – 800 sq. ft./gal. VOC: Vehicle Type: Dry Film Thickness/Coat: Density: Components: 1 Solids (% by Volume): Colors Available: Sheen: Ramuc Clean and Prep Application Guide: Overview: Ramuc Clean & Prep™ Solution is used to clean and degrease; while simultaneously dissolving mineral deposits and increasing porosity for good adhesion on surfaces for painting. It can be used on: painted surfaces, bare plaster, concrete or fiberglass. Clean & Prep is VOC compliant, odor and fume free, water-rinse neutralize and is biodegradable. It is safe to use near plants or grass and is excellent for filter element cleaning. Surface Preparation: After all surface repairs, power wash loose material off to a tight surface. For Bare Concrete, Gunite, Marcite or Plaster: Mix 1 gallon of Clean & Prep Solution with 2 gallons of water. Cleans approximately 400 square feet. Use garden sprayer for even application of product. Use Clean & Prep at a temperature no lower than 50° or higher than 85°F. Do not let solution set. Once solution is applied and foaming appears, begin scrubbing immediately with a stiff bristle brush/broom. Be sure the heavily soiled areas (such as waterline, steps or regular foot paths on concrete decks) are scrubbed well. After cleaning, triple rinse the surface using a garden hose (do not powerwash) with a strong, steady stream of clean water, while scrubbing to ensure complete removal of all material. Do not let the solution dry on the surface between rinsing. Rinse all at once. Triple rinsing is urged to ensure all of the solution is removed and the surface has been properly cleaned. Prior to painting with a solvent based coating, perform a condensation test per the instructions on the Ramuc product label to ensure a thoroughly dry surface. For Painted Surfaces or Bare Fiberglass: Mix 1 gallon Clean & Prep Solution with 5 gallons of water. Cleans approximately 600- 800 square feet. Use garden sprayer for even application of product. Use Clean & Prep at a temperature no lower than 50°F or higher than85°F. Do not let solution set. Once solution is applied and foaming appears, begin scrubbing immediately with a stiff bristle brush/broom. Be sure the heavily soiled areas (such as waterline, steps or regular foot paths on concrete decks) are scrubbed well. After cleaning, triple-rinse the surfaceusing a garden hose (do not powerwash) with a strong, steady stream of clean water, while scrubbing to ensure complete removal of all material. Do not let the solution dry on the surface between rinsing. Rinse all at once. Triple rinsing is urged to ensure all of the solution is removed and the surface has been properly cleaned. Prior to painting with a solvent based coating, perform a condensation test per the instructions on the Ramuc product label to ensure a thoroughly dry surface. For Pool Filter Elements: Mix 1 gallon of Clean and Prep solution to 5 gallons of hot water; soak for at least 1 hour, rinse and repeat if necessary to completely remove scum and mineral deposits.
